ASSRA Forum › General › Reloading the Single Shot Rifle › Schuetzen Loads
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 ... 3 4 [5]  Send TopicPrint
Very Hot Topic (More than 25 Replies) Schuetzen Loads (Read 214089 times)
Schuetzenmiester
Frequent Elocutionist
*****
Offline



Posts: 6707
Location: Cool Wet Side of WA
Joined: Apr 27th, 2008
Re: Schuetzen Loads
Reply #60 - Feb 2nd, 2019 at 2:52pm
Print Post  
ratseye wrote on Feb 1st, 2019 at 8:43am:
This is not exactly a Schuetzen rifle but I thought I would throw in my two cents. 

577-450 Martini reworked to Creedmoor style. 10x MVA model A scope. 29" original barrel in excellent condition. So far I have three, five shot groups under one inch at 100 yards benched. 

Bertram 577-450 brass
Federal LR Bench Rest Primer
22.1 grains Nobel Sport Vectan A0
4 grains Polyfill
Lee .429" 500 grain 3R unsized 16-1 alloy
Paper patched with tracing paper - Bore Butter patch lube
Seated to just touch
Avg - 1267 fps
SD - 7.1 fps

There is a picture in the photos section under "Reworked Martini" Thanks, Ratseye

Search cannot find it  Undecided
  
"some old things are lovely, warm still with life ... of the forgotten men who made them." - D.H. Lawrence
Back to top
 
IP Logged
 
ratseye
Full Member
***
Offline



Posts: 202
Location: Eastern, PA
Joined: Feb 28th, 2017
Re: Schuetzen Loads
Reply #61 - Feb 2nd, 2019 at 3:51pm
Print Post  
I tried searching for it too and it didn't come up. The post is there because I did find it. Strange. 

Here's another picture:



  
Back to top
 
IP Logged
 
art_ruggiero
Frequent Elocutionist
*****
Offline



Posts: 1183
Location: CT
Joined: Dec 14th, 2008
Re: Schuetzen Loads
Reply #62 - Feb 7th, 2019 at 2:20pm
Print Post  
ratseye:  how do you like the mva 10 x scope?  hows the field of view?   art
  
Back to top
 
IP Logged
 
ratseye
Full Member
***
Offline



Posts: 202
Location: Eastern, PA
Joined: Feb 28th, 2017
Re: Schuetzen Loads
Reply #63 - Feb 8th, 2019 at 8:05am
Print Post  
Art,

So far I like the scope a lot. I have two of their scopes and they are both pretty good all around. Clear and focused to the edges with a sharp crosshair. The field of view isn't bad but it is restricted somewhat. I don't remember the specification for it at the moment. I have a full length version on a Romano Spenser replica in 50-90 and it has held up well to the recoil. Their mounts hold zero and track well. I would likely buy another one if I needed something period correct.

Thanks, ratseye
  
Back to top
 
IP Logged
 
Dusty Rhodes
Full Member
***
Offline



Posts: 175
Joined: Apr 28th, 2016
Re: Schuetzen Loads
Reply #64 - Dec 6th, 2020 at 5:44pm
Print Post  
For the Ozzys 🇦🇺.
Martini Cadet with Sprinter 32/40 Varmint barrel. 1:16"
WW Cases, Fed 210 Primers.
ADI. 2207 @ 13.4 grn with cotton wool to hold.
N.O.E. Spitzer mold, 195grn. 20:1. Seated + Lite crimp.

Martini Cadet. Sprinter barrel.
WW case. Fed 210 primer.
ADI. 2207 @ 12.8grn with cotton wool.
N.O.E. Spitzer, 195grn @ 30:1. Breach seated.

Shutzen Low wall, 32/40, Douglas premium barrel. 
WW Case, Fed 210 primer.
Wano P @ 47.0grns. Drop tubed but not compressed. Drink coaster + Felt + Poly wad. 
N.O.E. Spitzer @ 30:1, SPG lube, Breach seated.
Wiped every shot with 1 x damp, Water and cutting oil @ 7%.

Low wall, Douglas 32/40.
WW Case, Fed 210 primer.
Wano P @ 47.0grns. Drop tubed but not compressed. Drink coaster + felt + poly wad. 
Hoch Tapered nose pour, 195grn @ 30:1, SPG lube, Breach seated. Wiped every shot with 1 x damp, water and cutting oil @ 7%.

No smokeless load for the Low wall. 


« Last Edit: Dec 6th, 2020 at 6:34pm by Dusty Rhodes »  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1 ... 3 4 [5] 
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.8887 seconds.