Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic 22 Niedner Magnum Rimmed (Read 194 times)
bobw
Frequent Elocutionist
*****
Offline



Posts: 2270
Joined: Mar 19th, 2013
22 Niedner Magnum Rimmed
Nov 17th, 2026 at 11:39pm
Print Post  
Looking for some help.

I have a rifle that I had to shorten the chambered barrel by a few thousands.  I recut the rim depth to spec., but the brass will not seat.  But, it would not seat prior to the barrel shortening.

I obviously have a shorter chamber, we are talking .008 off the barrel.

I’m wondering if the brass is sized, if it might work anyway.  But, I don’t have a sizing die for this cartridge.

So, I’m wondering if someone has a sizing die I could rent, borrow or something.  I have one piece of brass to try.

The other thing I might be looking for is a chamber reamer, just in case.  Although, this will be my last resort, and would not use it unless I was sure it would work to cut the chamber sightly deeper.

If you can help me please PM me.  Then if you need more explanation I would supply it.
Thanks
Bob



So, I’m
  
Back to top
 
IP Logged
 
Dellet
Frequent Elocutionist
*****
Offline



Posts: 1377
Joined: May 19th, 2017
Re: 22 Niedner Magnum Rimmed
Reply #1 - yesterday at 12:16am
Print Post  
If you can’t find a reamer, or dies, brass can probably be made using a 219 Donaldson die. Looking at the drawings, the body is shorter, and has a 30* shoulder. 219 zipper may also Take a look at the drawings 

If you think it might work, I’m more than happy to send you a couple pieces of brass or the forming die for the Donaldson. It looks like you could at least get something to fire form.
  
Back to top
 
IP Logged
 
guilty gil
Junior Member
**
Offline



Posts: 55
Location: Livingston mt.
Joined: Feb 5th, 2021
Re: 22 Niedner Magnum Rimmed
Reply #2 - yesterday at 8:28am
Print Post  
Google shows  powder valley has22 niedner dies for just under $22. Trim bottom of die to desired length?
  
Back to top
 
IP Logged
 
bobw
Frequent Elocutionist
*****
Offline



Posts: 2270
Joined: Mar 19th, 2013
Re: 22 Niedner Magnum Rimmed
Reply #3 - yesterday at 12:23pm
Print Post  
Dellet wrote yesterday at 12:16am:
If you can’t find a reamer, or dies, brass can probably be made using a 219 Donaldson die. Looking at the drawings, the body is shorter, and has a 30* shoulder. 219 zipper may also Take a look at the drawings 

If you think it might work, I’m more than happy to send you a couple pieces of brass or the forming die for the Donaldson. It looks like you could at least get something to fire form.


Thanks and yes, we were looking at the 219.  Here is the drawing I have of the 22 Niedner.  Also in the picture is the one piece of brass I have.  That brass was made from 25-35 brass as noted in the drawing.   

32-40 base is the same, or at least worked to test the firing pin positions and head space.  I did cut off the 32-40 at 1.250 and ran it through a 32-40 sizing die, just for testing purposes.

Thanks for the offer but we do have 25-35 brass available.
Bob
  
Back to top
 
IP Logged
 
bobw
Frequent Elocutionist
*****
Offline



Posts: 2270
Joined: Mar 19th, 2013
Re: 22 Niedner Magnum Rimmed
Reply #4 - yesterday at 12:31pm
Print Post  
guilty gil wrote yesterday at 8:28am:
Google shows  powder valley has22 niedner dies for just under $22. Trim bottom of die to desired length?



These are the dies I found.  As powder charging dies are they sizing dies also?
Thanks
Bob
  
Back to top
 
IP Logged
 
guilty gil
Junior Member
**
Offline



Posts: 55
Location: Livingston mt.
Joined: Feb 5th, 2021
Re: 22 Niedner Magnum Rimmed
Reply #5 - yesterday at 2:40pm
Print Post  
I don't know, i googled niedner dies & they came up .
  Didn't go to powder website.
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint