ASSRA Forum › General › Gunsmithing Single Shot Rifles › Ballard lever screw dimensions
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Ballard lever screw dimensions (Read 184 times)
cellargun
Full Member
***
Offline



Posts: 168
Joined: Feb 28th, 2022
Ballard lever screw dimensions
Apr 15th, 2026 at 1:58pm
Print Post  
As the title says, I need dimensions for a Ballard lever screw. I know I have seen it recently but search said no matches.
Memory says .277-40, but I would rather know for certain.
Thanks, Richard
  
Back to top
 
IP Logged
 
idjeffp
Senior Forum Member
****
Offline



Posts: 363
Location: Boise, ID
Joined: Nov 11th, 2017
Re: Ballard lever screw dimensions
Reply #1 - yesterday at 5:07pm
Print Post  
From a print I have... Hope this helps Wink
Jeff P
  
Back to top
 
IP Logged
 
KensBullard
Junior Member
**
Offline



Posts: 68
Location: Woodland Wa
Joined: Dec 17th, 2024
Re: Ballard lever screw dimensions
Reply #2 - yesterday at 11:06pm
Print Post  
Most of the scerw sizes in those Prints are off in someway off some not so far but most are off I have in my drawings of screws .227 X40 ken
  
Back to top
 
IP Logged
 
Airpistol
Participating Member
*
Offline



Posts: 12
Location: Idaho
Joined: Jan 21st, 2013
Re: Ballard lever screw dimensions
Reply #3 - Today at 11:29am
Print Post  
This is a thread on assra with the dimensions.   Posted by Kensmachine
Ballard screw threads as I see them   
Hammer & lever screw .227X40 no tap 
long lock, trigger, firing pin ret. long link & screw are the same screw ,short lock,tang sight screws,forearm screw,short link screw .172X40 clouses tap STI 6X40
trigger plate screws rear trigger spring .135X42 no tap
Tang screw 5/16 X 22 std special tap   
front trigger spring screw .090X48
Pacific forearm .109x48 4x48 std tap. 
from what I have been told by Ron Long is that all the threads on Cody Ballads where made with with off the shelf taps Ken
trigger adjustment screw .068X76
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 17908
Location: Oregon
Joined: Feb 2nd, 2009
Re: Ballard lever screw dimensions
Reply #4 - Today at 1:40pm
Print Post  
Airpistol wrote Today at 11:29am:
This is a thread on assra with the dimensions.   Posted by Kensmachine
Ballard screw threads as I see them  
Hammer & lever screw .227X40 no tap 
long lock, trigger, firing pin ret. long link & screw are the same screw ,short lock,tang sight screws,forearm screw,short link screw .172X40 clouses tap STI 6X40
trigger plate screws rear trigger spring .135X42 no tap
Tang screw 5/16 X 22 std special tap  
front trigger spring screw .090X48
Pacific forearm .109x48 4x48 std tap. 
from what I have been told by Ron Long is that all the threads on Cody Ballads where made with with off the shelf taps Ken
trigger adjustment screw .068X76


Kensmachine is now Kensbullard above.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 1.2373 seconds.