ASSRA Forum - Hepburn D.S.T.

ASSRA Forum › General › Gunsmithing Single Shot Rifles › Hepburn D.S.T.

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Hot Topic (More than 10 Replies)

Hepburn D.S.T. (Read 842 times)

4060may Full Member Offline Posts: 173 Location: Richfield Joined: Jul 12^th, 2006	Hepburn D.S.T. Jul 5^th, 2024 at 1:47pm	Print Post
	Adjusting screw on Hepburn DST front trigger size, thread pitch, where can I get one


	IP Logged

Old-Win Frequent Elocutionist Offline Posts: 1663 Location: Minnesota Joined: Nov 24^th, 2005	Re: Hepburn D.S.T. Reply #1 - Jul 5^th, 2024 at 3:04pm	Print Post
	Try DZ Arms or. C Sharps.


	IP Logged

4060may Full Member Offline Posts: 173 Location: Richfield Joined: Jul 12^th, 2006	Re: Hepburn D.S.T. Reply #2 - Jul 6^th, 2024 at 10:15am	Print Post
	talkedwith Dan yesterday , he uses 4-40


	IP Logged

Old-Win Frequent Elocutionist Offline Posts: 1663 Location: Minnesota Joined: Nov 24^th, 2005	Re: Hepburn D.S.T. Reply #3 - Jul 6^th, 2024 at 11:46am	Print Post
	Is that what the originals used?


	IP Logged

4060may Full Member Offline Posts: 173 Location: Richfield Joined: Jul 12^th, 2006	Re: Hepburn D.S.T. Reply #4 - Jul 6^th, 2024 at 1:57pm	Print Post
	no some bastard Remington screw I haven't removed the one I'm working on yet was covering my ... before I broke it off and, well you know


	IP Logged

steel-pounder Full Member Offline Posts: 135 Joined: Mar 26^th, 2016	Re: Hepburn D.S.T. Reply #5 - Jul 11^th, 2024 at 10:38am	Print Post
	its a 4-48 screw with a turned down section on the front and a .085 I think radius on the end. Mc master carr has socket head cap screws in stock in this size


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 15969 Location: Oregon Joined: Feb 2^nd, 2009	Re: Hepburn D.S.T. Reply #6 - Jul 11^th, 2024 at 6:19pm	Print Post
	steel-pounder wrote on Jul 11^th, 2024 at 10:38am: its a 4-48 screw with a turned down section on the front and a .085 I think radius on the end. Mc master carr has socket head cap screws in stock in this size Socket head screws will be a problem as there's not enough room to get a wrench into the head. Might need to cut the wrench down really short if you did use a socket head screw.

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

GT Frequent Elocutionist Offline Posts: 2028 Location: Northeast Wyoming Joined: Jun 28^th, 2015	Re: Hepburn D.S.T. Reply #7 - Jul 11^th, 2024 at 7:22pm	Print Post
	Here tis... .054 radius on the nose

	"To invent, you need a good imagination and a pile of junk" T. A. Edison "The trouble ain't that there is too many fools, but that the lightning ain't distributed right" M.T.
	IP Logged

kensmachine Oldtimer Offline Posts: 562 Joined: Nov 21^st, 2012	Re: Hepburn D.S.T. Reply #8 - Jul 11^th, 2024 at 10:37pm	Print Post
	some of the screws sizes on those prints are nowhere near right


	IP Logged

jhm Frequent Elocutionist Online Posts: 1379 Location: georgia Joined: Sep 4^th, 2011	Re: Hepburn D.S.T. Reply #9 - Jul 11^th, 2024 at 11:04pm	Print Post
	I have found that to be true. The casting sets I have done I normally try and use easily attainable common screw sizes for firearms. Unless I want to be absolutely true to original and then you have a hard time finding taps and dies for a lot of it to make the screws. Tried to make a few weird taps in past usually with dismal results. JMH


	IP Logged

steel-pounder Full Member Offline Posts: 135 Joined: Mar 26^th, 2016	Re: Hepburn D.S.T. Reply #10 - Jul 12^th, 2024 at 10:36am	Print Post
	marlinguy wrote on Jul 11^th, 2024 at 6:19pm: steel-pounder wrote on Jul 11^th, 2024 at 10:38am: its a 4-48 screw with a turned down section on the front and a .085 I think radius on the end. Mc master carr has socket head cap screws in stock in this size Socket head screws will be a problem as there's not enough room to get a wrench into the head. Might need to cut the wrench down really short if you did use a socket head screw. I have a socket head screw in mine. no problems with it. I used a ball end allen wrench to adjust it.


	IP Logged

4060may Full Member Offline Posts: 173 Location: Richfield Joined: Jul 12^th, 2006	Re: Hepburn D.S.T. Reply #11 - Jul 12^th, 2024 at 12:31pm	Print Post
	Thanks for all the information hopefully I can remove the old broken screw


	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.9133 seconds.