ASSRA Forum - relining 32 long barrel to 22 long rifle

ASSRA Forum › General › Gunsmithing Single Shot Rifles › relining 32 long barrel to 22 long rifle

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Hot Topic (More than 10 Replies)

relining 32 long barrel to 22 long rifle (Read 5652 times)

jeepjay Newbie Offline Posts: 4 Joined: Oct 8^th, 2015	relining 32 long barrel to 22 long rifle Mar 13^th, 2018 at 6:23pm	Print Post
	I have an old stevens favorite that was originally a 32 long caliber I would like to reline to 22 long rifle, I am wondering about the existing barrel inside diameter it appears to be just a few thousandths undersize for the liner except for the chamber area which is oversize of the liner, any suggestions on how to deal with this oversize area. thanks Jay


	IP Logged

GT Frequent Elocutionist Offline Posts: 2114 Location: Northeast Wyoming Joined: Jun 28^th, 2015	Re: relining 32 long barrel to 22 long rifle Reply #1 - Mar 13^th, 2018 at 7:40pm	Print Post
	Jay, I've done a couple of these- I started with a 7/16" drill ground a couple of steps, one is a short length existing chamber size another length at bore size long enough to reach past the chamber... Having a tool and cutter grinder available makes this easy. Not sure what tooling you have? A lathe? tool post grinder? more? I happen to have a few scrapped 6.5 barrels around so that became my material for another sleeve. The chamber end was drilled about 3-1/2" deep and I made the sleeve fit this fairly close, metal to metal maybe a .0005" loose. For this short section I did use tin and solder it in. Following this I set the barrel up and drilled it like any other liner job. I've used both Accraglass and Locktite install the liners and don't really have a preference. The 32 long groove diameter is right at the liner size, add some rust and corrosion and it's oversize. I finished drilling one once and didn't like what I saw, I etched the bore with a little muratic acid then rinsed it real well and let it dry. I then scrubbed with some contraband, (trichl. 1,1,1) and proceeded. May be a little excessive precaution but the rifle has probably had 20K rounds through it and there's no signs of giving up ground. Greg

	"To invent, you need a good imagination and a pile of junk" T. A. Edison "The trouble ain't that there is too many fools, but that the lightning ain't distributed right" M.T.
	IP Logged

jeepjay Newbie Offline Posts: 4 Joined: Oct 8^th, 2015	Re: relining 32 long barrel to 22 long rifle Reply #2 - Mar 13^th, 2018 at 8:04pm	Print Post
	thanks for the info, just what I needed, I do have a small machine shop and should be able to accomplish this. Jay


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 16730 Location: Oregon Joined: Feb 2^nd, 2009	Re: relining 32 long barrel to 22 long rifle Reply #3 - Mar 13^th, 2018 at 8:09pm	Print Post
	Just buy a TJ's liner. He offers them in various outside diameters and I know he has one that is 1/2" OD that will be plenty large and save doing two liners to get there.

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

WillH Junior Member Offline Posts: 76 Joined: May 20^th, 2013	Re: relining 32 long barrel to 22 long rifle Reply #4 - Mar 13^th, 2018 at 8:44pm	Print Post
	Forget the TJ liner and boring the barrel out to 1/2". The Brownell/Redman liner is top quality for 1/3 the price and Greg's installation advise is right on. Will


	AIM IP Logged

Deadeye Bly Frequent Elocutionist Offline Posts: 1088 Location: Stephens City Joined: Feb 25^th, 2011	Re: relining 32 long barrel to 22 long rifle Reply #5 - Mar 13^th, 2018 at 8:46pm	Print Post
	Both suggestions are valid. I've done them both ways. You can sleeve the chamber area first then drill out for a 5/16" liner. Not all 32 caliber barrels will clean up for the liner. The rimfire barrels generally will unless deeply pitted. TJ's makes 22 liners in 5/16", 3/8" and 1/2" diameters. If drilling it is a challenge you can send it to Bobby Hoyt and he will drill it for about $50. I've had him do several for me and then I install the liner and finish them up. I've only got a 5/16" diameter drill and this option lets me do more liners.


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 16730 Location: Oregon Joined: Feb 2^nd, 2009	Re: relining 32 long barrel to 22 long rifle Reply #6 - Mar 13^th, 2018 at 9:27pm	Print Post
	Yes, the 3/8" OD TJ's liner will be large enough to clean up the .32 bore.

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

John Boy Ex Member	Re: relining 32 long barrel to 22 long rifle Reply #7 - Mar 13^th, 2018 at 10:21pm	Print Post
	Jay, would you want to consider this instead putting in a liner... (You need to *Login* or *Register* to view media files and links)


	IP Logged

GT Frequent Elocutionist Offline Posts: 2114 Location: Northeast Wyoming Joined: Jun 28^th, 2015	Re: relining 32 long barrel to 22 long rifle Reply #8 - Mar 13^th, 2018 at 10:39pm	Print Post
	TJ's larger ones are an option and his liners are exceptional, I have used several with great success. My issue with going to a larger liner throughout is the amount of material removed from the entire barrel - if you go with a 3/8 or 1/2 od. The method I described is considerably more work but it leaves more material in the original. The Favorite's I've done recently, one octagon and one half and half -had muzzle diameters of .550 and .650 respectively, makes a thin tube to work with. Greg

	"To invent, you need a good imagination and a pile of junk" T. A. Edison "The trouble ain't that there is too many fools, but that the lightning ain't distributed right" M.T.
	IP Logged

ten-mile Full Member Offline Posts: 165 Location: Chetek Joined: Dec 8^th, 2007	Re: relining 32 long barrel to 22 long rifle Reply #9 - Mar 14^th, 2018 at 7:38am	Print Post
	Look on GunBroker for 32RF adapters that are made from drawn brass instead of bar stock and at half the price. (You need to *Login* or *Register* to view media files and links) Going with a 22 reline is a lot less hassle in the long run though.


	WWW IP Logged

jeepjay Newbie Offline Posts: 4 Joined: Oct 8^th, 2015	Re: relining 32 long barrel to 22 long rifle Reply #10 - Mar 14^th, 2018 at 11:28am	Print Post
	thanks for all the advice, the inside of the barrel does show rifling but does not look real shiny I doubt it would be a good shooter with 32 ammo, I have completely replaced the barrel on another favorite that I have and that was fairly straightforward but this old 32 barrel is in real nice shape on the outside so a reline is my plan moving forward, thanks again for all the info and advice Jay


	IP Logged

John Taylor Frequent Elocutionist Offline Posts: 1755 Location: Lewiston, ID Joined: Oct 23^rd, 2006	Re: relining 32 long barrel to 22 long rifle Reply #11 - Mar 15^th, 2018 at 12:32am	Print Post
	I did a 32 to 22 for myself a while back. The bore was very close so I ran a 5/16" drill ( no pilot ) bit through it an the liner went in just fine. I soldered a sleeve on the end of the liner and turn it to fit the chamber. A little Loctite and it was in to stay. This was done on a Frank Wesson with a 30" barrel and hand ejector. I like the liners from T.J.'s and have used them for almost 20 years.

	John Taylor Machinist/gunsmith
	WWW IP Logged

jeepjay Newbie Offline Posts: 4 Joined: Oct 8^th, 2015	Re: relining 32 long barrel to 22 long rifle Reply #12 - Mar 28^th, 2018 at 2:20am	Print Post
	got the barrel relined and the rifle ready to shoot, everything worked out nice, thanks for all the good advice. Jay


	IP Logged

kensmachine Oldtimer Offline Posts: 574 Joined: Nov 21^st, 2012	Re: relining 32 long barrel to 22 long rifle Reply #13 - Mar 28^th, 2018 at 10:43am	Print Post
	I will never ever use a Redman service or product again 1 time was enough Ken


	IP Logged

Redsetter Frequent Elocutionist Offline Posts: 3468 Location: New York Joined: Aug 6^th, 2013	Re: relining 32 long barrel to 22 long rifle Reply #14 - Mar 28^th, 2018 at 11:57am	Print Post
	kensmachine wrote on Mar 28^th, 2018 at 10:43am: I will never ever use a Redman service or product again 1 time was enough Ken For me too! Especially after he told me, when I expressed disappointment over the accuracy, that I'd probably have to fire 1000 rounds or more before its full accuracy was achieved. On a .22RF? Installed by him? This was 25 yrs ago, so maybe he's improved, but it's not a thing I'd be eager to do again.


	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 1.1499 seconds.