ASSRA Forum › General › Gunsmithing Single Shot Rifles › Low wall with Rigby Flats
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 2 [3]  Send TopicPrint
Very Hot Topic (More than 25 Replies) Low wall with Rigby Flats (Read 9531 times)
SSShooter
Frequent Elocutionist
*****
Offline



Posts: 2932
Location: Southern NJ
Joined: Aug 1st, 2010
Re: Low wall with Rigby Flats
Reply #30 - Mar 7th, 2018 at 8:06am
Print Post  
jhm wrote on Feb 18th, 2018 at 7:30pm:
I have a Stevens 45 I would like to have a small amount of engraving done but when I asked about pricing found it to be quite expensive so guess it will have to wait.
JMH

How much are you willing to spend? I've always set a budget and then contacted the engraver, giving them a broad outline of what I would like, but let them finalize the design. Have always ask for a border plus whatever they are willing to fit in above that for my budget. Have gotten three very nice receivers back. You can see the engraving on all in this thread:
(You need to Login or Register to view media files and links)

  
Glenn - Stevens 044 1/2, Bartlein SS 5R barrel in 22LR
Back to top
GTalk  
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 16717
Location: Oregon
Joined: Feb 2nd, 2009
Re: Low wall with Rigby Flats
Reply #31 - Mar 7th, 2018 at 12:12pm
Print Post  
Don't forget to add in annealing the receiver, as most engravers will require any case colored receiver to be annealed prior to engraving. I use a gunsmith who anneals mine for free if I'm going to have him do the color case also.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
jhm
Frequent Elocutionist
*****
Offline



Posts: 1670
Location: georgia
Joined: Sep 4th, 2011
Re: Low wall with Rigby Flats
Reply #32 - Mar 7th, 2018 at 4:38pm
Print Post  
SSShooter.....

Can you recommend someone? Maybe if I talk to someone and get some advise on prices I can go from there.


Thanks

JMH
  
Back to top
 
IP Logged
 
jfeldman
ASSRA Board Member
*****
Offline



Posts: 1088
Location: Imperial Beach, Ca
Joined: Nov 5th, 2005
Re: Low wall with Rigby Flats
Reply #33 - Mar 8th, 2018 at 12:25am
Print Post  
jhm, here's a link to Dale Woody's site.  He has examples and prices so you can get some ideas................

(You need to Login or Register to view media files and links)

Regards, Joe
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 16717
Location: Oregon
Joined: Feb 2nd, 2009
Re: Low wall with Rigby Flats
Reply #34 - Mar 8th, 2018 at 12:14pm
Print Post  
jfeldman wrote on Mar 8th, 2018 at 12:25am:
jhm, here's a link to Dale Woody's site.  He has examples and prices so you can get some ideas................

(You need to Login or Register to view media files and links)

Regards, Joe


Don't think you'll get anywhere with Dale. He had a major stroke a year ago, and I haven't been able to get any reply from him via phone or email since. Haven't even been able to find anyone who can confirm his condition today.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1 2 [3] 
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.6939 seconds.