ASSRA Forum › General › Gunsmithing Single Shot Rifles › Low Wall Breech Block Issues
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Low Wall Breech Block Issues (Read 2305 times)
FourBird
Participating Member
*
Offline



Posts: 46
Location: Olympia, WA
Joined: Oct 13th, 2011
Low Wall Breech Block Issues
Mar 16th, 2015 at 7:21am
Print Post  
Can these breech blocks be saved?

#1.  Appears to have been in a fire.  Firing pin and retaining screw fused in the block.

#2.  At some point in time the firing pin retaining screw was crudely drilled out.  No threads remain.

All comments/suggestions/ideas  appreciated.
  
Limit Politicians to two terms:  Office immediately followed by Prison (life w/out parole).
Back to top
 
IP Logged
 
frnkeore
Frequent Elocutionist
*****
Offline



Posts: 7283
Location: Central Point, OR 97502
Joined: Jun 16th, 2010
Re: Low Wall Breech Block Issues
Reply #1 - Mar 16th, 2015 at 1:13pm
Print Post  
I think both can be salaged:

#1, getting the firing pin out w/o damaging the block, won't be easy but, it should be annealed now and easy to machine. It can be CCH after.

#2, It sounds saveable, too but, you'll have to juggle hole and thread size and maybe make a threaded or press in bushing to fix it.

Frank
  
ASSRA Member #696, ISSA Member #339
Back to top
YIMAIM  
IP Logged
 
AJ
Full Member
***
Offline



Posts: 141
Joined: Aug 25th, 2011
Re: Low Wall Breech Block Issues
Reply #2 - Mar 16th, 2015 at 5:51pm
Print Post  
I'd start by soaking it a few days in a 50/50 mix of acetone and automatic transmission fluid.  You have to shake the mix occasionally as it wants to separate.  It is the best thing I've found for loosening frozen parts.  If that doesn't work, try heating the block to 2-300 degrees and tapping on the firing pin.
  
Back to top
 
IP Logged
 
SSShooter
Frequent Elocutionist
*****
Offline



Posts: 2917
Location: Southern NJ
Joined: Aug 1st, 2010
Re: Low Wall Breech Block Issues
Reply #3 - Mar 17th, 2015 at 7:11am
Print Post  
Take it to John Taylor Machine in Puyallup and pick it up when he tells you he is finished.
  
Glenn - 2x CPA 44 1/2 w/22LR (Shilen ratchet-rifled & Bartlein 5R rifled), 38-40RH & 38-55WCF (Bartlein 5R rifled) & 40-65WCF (GrnMtn 'X') barrels
Back to top
GTalk  
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 16159
Location: Oregon
Joined: Feb 2nd, 2009
Re: Low Wall Breech Block Issues
Reply #4 - Mar 17th, 2015 at 12:01pm
Print Post  
SSShooter wrote on Mar 17th, 2015 at 7:11am:
Take it to John Taylor Machine in Puyallup and pick it up when he tells you he is finished.


Excellent idea, considering how close they are!
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.7266 seconds.