Page Index Toggle Pages: 1 Send TopicPrint
Hot Topic (More than 10 Replies) Question about relining (Read 395 times)
CW
Oldtimer
*****
Offline



Posts: 562
Joined: Feb 20th, 2018
Question about relining
Nov 14th, 2026 at 3:56pm
Print Post  
I have a cast action Ballard rifle and sometime in the past someone lined it to 38-40 using a 5/8" liner. The rechambering quality was exceedingly poor and it is kinda a 4" group, 100 yard shooter.

Between the poor accuracy and me wanting to rechamber to a smaller case head (32-20WCF or 25-20WCF) for pressure concerns, I am stuck with this old 5/8" liner.

If it is removed, there are no 5/8" 32-20 replacements from TJ's or Redman. Those aren't options.

Just drilling out the existing 5/8th" liner to 1/2" and installing the 1/2" TJ's 32-20 liner works operationally, but is that a real safe option?
  
Back to top
 
IP Logged
 
Oldman1950
Senior Forum Member
****
Offline



Posts: 306
Location: Virginia
Joined: Feb 8th, 2014
Re: Question about relining
Reply #1 - Nov 14th, 2026 at 4:33pm
Print Post  
How is the liner held in? Solder, Epoxy, Bubble gum?
Once the liner is removed it sounds like you will need a rifle barrel with the bore and twist that you like and then turn it on a lathe to the outside dimension to fit the barrel that you want to reline.

A. J. Palik
  
Back to top
 
IP Logged
 
Oldman1950
Senior Forum Member
****
Offline



Posts: 306
Location: Virginia
Joined: Feb 8th, 2014
Re: Question about relining
Reply #2 - Nov 14th, 2026 at 8:44pm
Print Post  
SORRY about the wise crack about bubble gum Wink
  
Back to top
 
IP Logged
 
Sure shot
Frequent Elocutionist
*****
Online



Posts: 1249
Location: East central Iowa
Joined: Jun 22nd, 2020
Re: Question about relining
Reply #3 - yesterday at 4:10am
Print Post  
If they used the red loctite, it may be nearly impossible to remove the liner without drilling it out.
  
Back to top
 
IP Logged
 
TomKlinger
Senior Forum Member
****
Online



Posts: 313
Location: Central Florida
Joined: Feb 17th, 2019
Re: Question about relining
Reply #4 - yesterday at 6:20am
Print Post  
Call Todd at TJs I think he can make you a 5/8 32/20 liner.


Tom Klinger

PS I’ve never been successful at removing an old liner without drilling……
  
Back to top
 
IP Logged
 
Oldman1950
Senior Forum Member
****
Offline



Posts: 306
Location: Virginia
Joined: Feb 8th, 2014
Re: Question about relining
Reply #5 - yesterday at 1:33pm
Print Post  
Temperature at Which Loctite Breaks Down
Loctite threadlockers do not all “break down” at the same temperature — the limit depends on the specific grade, but most standard red grades (e.g., 271, 263) are rated up to about 300–360 °F, and high‑temperature grades can survive up to 450–650 °F before losing strength or becoming removable with heat 
bing.com
bing.com
+1
.

How Loctite Heat Resistance Works
Loctite products are anaerobic adhesives that cure in the absence of oxygen. Once cured, they retain strength well below their maximum service temperature, but above certain thresholds they soften enough to be removed with heat. This is why manufacturers recommend localized heating for disassembly.

Standard high‑strength red grades (e.g., Loctite 271, 263)

Max service temp: 300 °F (271) to 360 °F (263) 
STS Industrial
STS Industrial
+1

Removal: Henkel specifies heating the nut or bolt to ~500 °F to soften the adhesive enough to break loose 
STS Industrial
STS Industrial
.

Practical breakdown: In service, these grades often start to lose holding strength around 325–400 °F and will release more easily once heated above ~500 °F 
Practical Machinist
Practical Machinist
+1
.

High‑temperature red grades (e.g., 266, 272)

Max service temp: up to 450 °F 
STS Industrial
STS Industrial

Removal: Still require ~500 °F for easy disassembly, but can withstand sustained operation at higher temps than standard red grades.

Ultra‑high‑temperature grades (e.g., 2422, 2620)

Max service temp: up to 650 °F 
bing.com
bing.com
+1

Removal: Similar heat‑softening behavior; removal still requires localized heating above ~500 °F.

Key Points
Breakdown ≠ melting — Loctite doesn’t “melt” like plastic; it softens and loses shear strength as temperature rises.

Service limit vs. removal limit — The “max service temp” is the highest continuous operating temperature; the “removal” temperature is higher, where the adhesive becomes soft enough to be loosened with heat.

Grade matters — Always check the product data sheet for the exact temperature range and removal instructions.

Practical tip — For standard red Loctite, expect it to start losing strength above ~325–400 °F and to be removable with heat above ~500 °F 
Practical Machinist
Practical Machinist
+1
.

Example: Loctite 271 (high strength red) is rated to 300 °F service, but will release with localized heating at ~500 °F 
STS Industrial
STS Industrial
. Loctite 266 (high temp red) is rated to 450 °F service, still requiring ~500 °F for removal 
STS Industrial
STS Industrial
.

If you need a fastener to stay secure at high operating temperatures, choose a grade rated for that range and be aware that heat removal will still be required for disassembly.
  
Back to top
 
IP Logged
 
CW
Oldtimer
*****
Offline



Posts: 562
Joined: Feb 20th, 2018
Re: Question about relining
Reply #6 - yesterday at 7:40pm
Print Post  
Oldman1950 wrote on Nov 14th, 2026 at 8:44pm:
SORRY about the wise crack about bubble gum Wink


It is okay, I have a sense of irony and thrive on abuse. I was married to a redhead for many years.
  
Back to top
 
IP Logged
 
CW
Oldtimer
*****
Offline



Posts: 562
Joined: Feb 20th, 2018
Re: Question about relining
Reply #7 - yesterday at 7:43pm
Print Post  
TomKlinger wrote yesterday at 6:20am:
Call Todd at TJs I think he can make you a 5/8 32/20 liner.
Tom Klinger
PS I’ve never been successful at removing an old liner without drilling……


That is a good idea. Who knows, but I will give him a call this week and see. Even if it costs a bit extra, it could be the deal in the long run.
  
Back to top
 
IP Logged
 
CW
Oldtimer
*****
Offline



Posts: 562
Joined: Feb 20th, 2018
Re: Question about relining
Reply #8 - yesterday at 7:49pm
Print Post  
BTW -  this thread was intended to go into the Gunsmithing area. To start the thread, I moved the mouse and clicked on Gunsmithing .....and missed. The  "bad aim" isn't just with rifles.
  
Back to top
 
IP Logged
 
Sure shot
Frequent Elocutionist
*****
Online



Posts: 1249
Location: East central Iowa
Joined: Jun 22nd, 2020
Re: Question about relining
Reply #9 - Today at 12:36pm
Print Post  
I've removed soldered in liners by putting the barrel in my kitchen oven and leaving it in long enough to get it completely up to 400 plus degrees. The liner slid right out with the aid of pliers. I had a cleaning rod handy with patches to help remove any remaining solder inside of the barrel. Placing the barrel in kitty-corner, it just fit in the oven. I tried the same method at 500 degrees to remove a liner that was secured with red loctite, no-go. Even with placing the barrel back in the oven and with considerable hammering on it,it wouldn't come out. It was drilled out later.
  
Back to top
 
IP Logged
 
bobw
Frequent Elocutionist
*****
Offline



Posts: 2267
Joined: Mar 19th, 2013
Re: Question about relining
Reply #10 - Today at 12:42pm
Print Post  
Sure shot wrote Today at 12:36pm:
I've removed soldered in liners by putting the barrel in my kitchen oven and leaving it in long enough to get it completely up to 400 plus degrees. The liner slid right out with the aid of pliers. I had a cleaning rod handy with patches to help remove any remaining solder inside of the barrel. Placing the barrel in kitty-corner, it just fit in the oven. I tried the same method at 500 degrees to remove a liner that was secured with red loctite, no-go. Even with placing the barrel back in the oven and with considerable hammering on it,it wouldn't come out. It was drilled out later.


LOL, I guess that answers the question of “will large caliber liners coming loose” if they are glued in!
Bob
  
Back to top
 
IP Logged
 
jhm
Frequent Elocutionist
*****
Offline



Posts: 2168
Location: georgia
Joined: Sep 4th, 2011
Re: Question about relining
Reply #11 - Today at 5:57pm
Print Post  
Yep my fears have been laid to rest...




JMH
  
Back to top
YouTube  
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint