ASSRA Forum › General › Gunsmithing Single Shot Rifles › Optimum 32 Caliber barrel length..?
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Optimum 32 Caliber barrel length..? (Read 145 times)
RJ-35-40
Senior Forum Member
****
Offline



Posts: 280
Joined: Dec 7th, 2016
Optimum 32 Caliber barrel length..?
Yesterday at 11:46am
Print Post  
Optimum 32 Caliber barrel length..?

This is a long shot ball park inquiry,  so please ignore if there is too much involved. 

So I have a 34.75" X 1" 32 cal gain twist barrel blank. (Round)
I am planning on having chambered & fitted on a Hi Wall.

If someone out there has "Quick Load" or similar loading software, would you please give me a "rough" idea of how many inches of barrel travel would a 200 grain projectile have to traverse in order to complete the combustion process with any one of the listed powders that I have in stock. I'm hoping to ultimately find a combination utilizing either a 32 Miller / short or similar cartridge akin to 32-40 short / 32-357 case.

Looking to keep it about 1350-1400 fps. 

In stock powders:
Enforcer
WC820
300MP
H322
1680

Any thoughts in general are appreciated.
If I had a lathe (and a gunsmith who was so skilled) I could just pick a cartridge and experiment by testing by cutting off an inch at a time.

THX

Bob
  
Back to top
 
IP Logged
 
calledflyer
Frequent Elocutionist
*****
Offline



Posts: 3924
Joined: Mar 9th, 2015
Re: Optimum 32 Caliber barrel length..?
Reply #1 - yesterday at 12:00pm
Print Post  
Well, if it were a project I was having done, the gunpowder would be among the last parts of the questions to answer. Intended use would be most of the parts to worry about- weight, offhand or bench, intended bullet(s) to determine twist (seems already done here) and sighting radius if no scope is planned. My guess is that in many loadings the mentioned powders would all be able to be consumed unless you end up building a snub-nose .32. Just my take on your question.
  
Back to top
 
IP Logged
 
Schuetzendave
Frequent Elocutionist
*****
Offline


Retired Ex-Shooter

Posts: 4219
Location: St. Albert, Alberta
Joined: Jan 28th, 2005
Re: Optimum 32 Caliber barrel length..?
Reply #2 - yesterday at 1:02pm
Print Post  
Basically a 30 inch barrel is required to burn black powder before it exits the barrel. 

For the longer cases with more black powder compressed inside; and the bullet exposed to increase the case capacity, a bit longer barrel may be required to combust all of the black powder in a barrel.

Smokeless powder combusts more rapidly and is fully used to maximize barrel pressures in barrels 22 inches long.

After the powder is completely combusted within the barrel to maximize the optimum pressures any additional barrel length will not improve accuracy when using scopes.

However longer barrels minimizes sight angle for shooting iron sights so then a longer barrel does improve your ability to shoot more accurately.

The testing of barrels by cutting off an inch at a time has already been done and we already know that you need at least a 22 inch barrel length to shoot the smokeless powders you have listed.
  
Back to top
 
IP Logged
 
RJ-35-40
Senior Forum Member
****
Offline



Posts: 280
Joined: Dec 7th, 2016
Re: Optimum 32 Caliber barrel length..?
Reply #3 - yesterday at 1:22pm
Print Post  
Called Flyer,

Thanks for the clarifying observations, the following is what I am contemplating 

1, A bench gun,
2, Weight of rifle, N/A see #1
3, 200 grain bullet range
4, Sight radius, probably scoped but if I were to use a tang mounted vernier sight I would expect that as close to 36" sight radius would be desirable

I do have a 32-40 with a 26" barrel which might get me some idea of powder ignition percentage, but due to the larger case capacity I think the ignition characteristics will change.
 
Given that the 32-40 is oversized (inefficient @ + - 2" long) for most smokeless powder charges (13-14 gr. I shoot in a 32-20) I really want to explore the shorter 32 cartridge case profiles to get in the 90% + case full range. 

Honestly I have not done much shooting in this realm to have baseline knowledge. 

 
calledflyer wrote yesterday at 12:00pm:
Well, if it were a project I was having done, the gunpowder would be among the last parts of the questions to answer. Intended use would be most of the parts to worry about- weight, offhand or bench, intended bullet(s) to determine twist (seems already done here) and sighting radius if no scope is planned. My guess is that in many loadings the mentioned powders would all be able to be consumed unless you end up building a snub-nose .32. Just my take on your question.

  
Back to top
 
IP Logged
 
RJ-35-40
Senior Forum Member
****
Offline



Posts: 280
Joined: Dec 7th, 2016
Re: Optimum 32 Caliber barrel length..?
Reply #4 - yesterday at 1:30pm
Print Post  
DAVE,

Thanks for your insights.. I really appreciate the BP vs. smokeless observation. 

As I enjoy experimenting I was thinking of having two different barrels fitted for this action. 

At my age I better get busy so I can use up my stockpiles of components. 

RJ

Schuetzendave wrote yesterday at 1:02pm:
Basically a 30 inch barrel is required to burn black powder before it exits the barrel. 

For the longer cases with more black powder compressed inside; and the bullet exposed to increase the case capacity, a bit longer barrel may be required to combust all of the black powder in a barrel.

Smokeless powder combusts more rapidly and is fully used to maximize barrel pressures in barrels 22 inches long.

After the powder is completely combusted within the barrel to maximize the optimum pressures any additional barrel length will not improve accuracy when using scopes.

However longer barrels minimizes sight angle for shooting iron sights so then a longer barrel does improve your ability to shoot more accurately.

The testing of barrels by cutting off an inch at a time has already been done and we already know that you need at least a 22 inch barrel length to shoot the smokeless powders you have listed.

  
Back to top
 
IP Logged
 
GT
Frequent Elocutionist
*****
Offline



Posts: 2340
Location: Northeast Wyoming
Joined: Jun 28th, 2015
Re: Optimum 32 Caliber barrel length..?
Reply #5 - yesterday at 3:14pm
Print Post  
RJ,
Just throwing this out there, if you were cutting an inch at a time off the barrel with a gain twist, you'd want to do it from the chamber end.  That means re-chamber each time, cut the extractor each time, etc.   
For a bench rifle, personally I prefer the heft.  Length, I'd go 30" to 31".  Some say shortening below that is better, if you jerk rather than squeeze a 26" barrel gives you less time for the bullet to be disturbed on it's path, I'm not a believer in that - you practice bench methods to eliminate that part of the equation.    The sight radius that works about the best for irons if you do the math, is 34.378".  That calulates to .010 on your staff to one minute when making adjustments.  A 30" or 31" barrel with most actions allows you to get to that length.
My 2¢ 
GT
  
"To invent, you need a good imagination and a pile of junk"  T. A. Edison
"The trouble ain't that there is too many fools, but that the lightning ain't distributed right" M.T.
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 17872
Location: Oregon
Joined: Feb 2nd, 2009
Re: Optimum 32 Caliber barrel length..?
Reply #6 - yesterday at 5:31pm
Print Post  
All my rifles with barrels by old masters like Pope, Schoyen, etc. are all 32"-34" barrels, and shoot well with heavy .32-40 bullets. None are gain twist, but they are faster twists for the era they were built. Now days a lot of guys shoot even faster twist than what used to be considered fast.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
bpjack
Frequent Elocutionist
*****
Offline



Posts: 3681
Location: East Olympia, WA
Joined: May 18th, 2008
Re: Optimum 32 Caliber barrel length..?
Reply #7 - yesterday at 5:40pm
Print Post  
My 32-40 14 twist Green Mountain barreled high wall has a 31" barrel and although it has shot very well (2 match 250s) with some loads the last inch seems to be fouled more.  My 32-40 12 twist Douglas barreled high wall shoots just as good with its 28" barrel.
  
ASSRA # 11318
Experience is something you don't get until just after you need it.
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 17872
Location: Oregon
Joined: Feb 2nd, 2009
Re: Optimum 32 Caliber barrel length..?
Reply #8 - yesterday at 6:45pm
Print Post  
bpjack wrote yesterday at 5:40pm:
My 32-40 14 twist Green Mountain barreled high wall has a 31" barrel and although it has shot very well (2 match 250s) with some loads the last inch seems to be fouled more.  My 32-40 12 twist Douglas barreled high wall shoots just as good with its 28" barrel.


Are you getting a good lube star on the muzzle Jack?
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.4146 seconds.