ASSRA Forum - Schoyen Style Stock on a Ballard

ASSRA Forum › General › Gunsmithing Single Shot Rifles › Schoyen Style Stock on a Ballard

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1 [2]

Schoyen Style Stock on a Ballard (Read 343 times)

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 17663 Location: Oregon Joined: Feb 2^nd, 2009	Re: Schoyen Style Stock on a Ballard Reply #15 - Today at 5:32pm	Print Post
	What type of disc do you use for the rough shaping Bob? Is it like a flapper disc, or what? Beautiful stock work, even at this early stages!

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

bobw Frequent Elocutionist Offline Posts: 2010 Location: NW, Iowa Joined: Mar 19^th, 2013	Re: Schoyen Style Stock on a Ballard Reply #16 - Today at 5:48pm	Print Post
	Vall, the disc looks like shingles, overlapping each section. I use the 36 grit and stiff enough you can put lots of pressure on it if you want too. I know there is a rasp like cutter and would probably try one except our hardware store doesn’t carry it. For 3 buck each I just use these. One does a one stock unless the wood is rock hard. Normally the grinding takes me 15-20 minutes. But the day I did this one it was 10 degrees. I’m not know for wearing a coat, so I would work for a few minutes until my hands got cold, then go in, do something else and warm up. Took 2 hours using this cycle. Bob
	« Last Edit: Today* at 5:54pm by bobw* »
	Robert Warren
	IP Logged

calledflyer Frequent Elocutionist Offline Posts: 3878 Joined: Mar 9^th, 2015	Re: Schoyen Style Stock on a Ballard Reply #17 - Today at 6:24pm	Print Post
	I did a lot of cabinet building in cold weather, so I know how the coolness can feel. I dunno how you guys up there can take much more of this. My hat is off to you (no need to doff yours in return- too damn cold!) But, I sure am enjoying the results here like I did a while back when you were stocking the Walker Hepburn. Super work on stunning wood.


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 17663 Location: Oregon Joined: Feb 2^nd, 2009	Re: Schoyen Style Stock on a Ballard Reply #18 - Today at 8:54pm	Print Post
	bobw wrote Today at 5:48pm: Vall, the disc looks like shingles, overlapping each section. I use the 36 grit and stiff enough you can put lots of pressure on it if you want too. I know there is a rasp like cutter and would probably try one except our hardware store doesn’t carry it. For 3 buck each I just use these. One does a one stock unless the wood is rock hard. Normally the grinding takes me 15-20 minutes. But the day I did this one it was 10 degrees. I’m not know for wearing a coat, so I would work for a few minutes until my hands got cold, then go in, do something else and warm up. Took 2 hours using this cycle. Bob Thanks Bob! I have bunches of those I use in metal fab work for years. They're what we call flapper discs. (You need to *Login* or *Register* to view media files and links)

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

Pages: 1 [2]

‹ Previous Topic | Next Topic ›

Page completed in 1.1047 seconds.