ASSRA Forum - Any High Wall Zettler triggers out there?

ASSRA Forum › General › Gunsmithing Single Shot Rifles › Any High Wall Zettler triggers out there?

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: [1] 2 3

Very Hot Topic (More than 25 Replies)

Any High Wall Zettler triggers out there? (Read 767 times)

bpjack Frequent Elocutionist Offline Posts: 3514 Location: East Olympia, WA Joined: May 18^th, 2008	Any High Wall Zettler triggers out there? Nov 28^th, 2025 at 1:52pm	Print Post
	I am trying to install a set of triggers from eBay and the knockoff isn't even coming close enough to trip the long tailed sear. I wonder if they require a different shaped sear? Anyone have one? I would like to see a photo of the sear. Thanks Jack

	ASSRA # 11318 Experience is something you don't get until just after you need it.
	IP Logged

westerner Frequent Elocutionist Offline deleted posts and threads record holder. Posts: 12043 Location: Why, out West of course Joined: May 29^th, 2006	Re: Any High Wall Zettler triggers out there? Reply #1 - Nov 28^th, 2025 at 1:58pm	Print Post
	Can you bend your sear down? Most likely have to anneal it first. Make a new sear.

	A blind squirrel runs into a tree every once in a while.
	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3514 Location: East Olympia, WA Joined: May 18^th, 2008	Re: Any High Wall Zettler triggers out there? Reply #2 - Nov 28^th, 2025 at 2:29pm	Print Post
	That is a possibility. Currently when it doesn't trip, you can pull back on the rear trigger to manually trip the sear but if it were bent don, it probably wouldn't reach. I am thinking maybe bending a long tail sear and adding some length. That is why it would be nice to see one that works.

	ASSRA # 11318 Experience is something you don't get until just after you need it.
	IP Logged

westerner Frequent Elocutionist Offline deleted posts and threads record holder. Posts: 12043 Location: Why, out West of course Joined: May 29^th, 2006	Re: Any High Wall Zettler triggers out there? Reply #3 - Nov 28^th, 2025 at 2:36pm	Print Post
	I mean the sear that's pinned to the action.

	A blind squirrel runs into a tree every once in a while.
	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3514 Location: East Olympia, WA Joined: May 18^th, 2008	Re: Any High Wall Zettler triggers out there? Reply #4 - Nov 28^th, 2025 at 2:42pm	Print Post
	That is what I am talking about too. I will get a photo later. It actually stopped raining and I need to get to work on the Ark before the rains come back.. I have the base ready...

	ASSRA # 11318 Experience is something you don't get until just after you need it.
	IP Logged

GT Frequent Elocutionist Offline Posts: 2281 Location: Northeast Wyoming Joined: Jun 28^th, 2015	Re: Any High Wall Zettler triggers out there? Reply #5 - Nov 28^th, 2025 at 8:35pm	Print Post
	Not the right size... 40 cubits? You're too short.

	"To invent, you need a good imagination and a pile of junk" T. A. Edison "The trouble ain't that there is too many fools, but that the lightning ain't distributed right" M.T.
	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3514 Location: East Olympia, WA Joined: May 18^th, 2008	Re: Any High Wall Zettler triggers out there? Reply #6 - Nov 28^th, 2025 at 9:02pm	Print Post
	I just in charge of collecting 2 each of all the slugs native to the northwest.

	ASSRA # 11318 Experience is something you don't get until just after you need it.
	IP Logged

Schutzenbob Frequent Elocutionist Online Rheinisch-Westfälisc hen Sprengstoff-Fabriken Posts: 2207 Location: Nightingale, California Joined: Oct 24^th, 2005	Re: Any High Wall Zettler triggers out there? Reply #7 - Nov 28^th, 2025 at 9:48pm	Print Post
	Aye Jack, Can you post a pic of the top of the triggers?


	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3514 Location: East Olympia, WA Joined: May 18^th, 2008	Re: Any High Wall Zettler triggers out there? Reply #8 - Nov 28^th, 2025 at 10:00pm	Print Post
	I plan on doing that in a while. Got to finish watching Survivor and do the dishes. I just had a thought. I could d&t a hole in the long tail seat and install a flat head screw for the knockoff to hit. Adjustable too.

	ASSRA # 11318 Experience is something you don't get until just after you need it.
	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3514 Location: East Olympia, WA Joined: May 18^th, 2008	Re: Any High Wall Zettler triggers out there? Reply #9 - Nov 28^th, 2025 at 11:13pm	Print Post
	Here are some photos. One shows the top. The next shoes the side with the knockoff portion raised as high as it will go. The last shows the gap between the knockoff at its highest and the tail of the sear at 1/2 cock.

	ASSRA # 11318 Experience is something you don't get until just after you need it.
	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3514 Location: East Olympia, WA Joined: May 18^th, 2008	Re: Any High Wall Zettler triggers out there? Reply #10 - Nov 28^th, 2025 at 11:36pm	Print Post
	For a test, I scrounged up a small piece of brass rectangular stock and used some double sided carpet tape to hold it in place. This works just fine. I did back off on the sear spring so I want to tighten it up tomorrow and epoxy a nicer brass shim in place. I could probably just build it up with some brazing rod and file to shape. It is a new MVA long tailed sear so I am not worried about screwing it up. Jack

	ASSRA # 11318 Experience is something you don't get until just after you need it.
	IP Logged

Old-Win Frequent Elocutionist Offline Posts: 1787 Location: Minnesota Joined: Nov 24^th, 2005	Re: Any High Wall Zettler triggers out there? Reply #11 - Nov 29^th, 2025 at 8:22am	Print Post
	Jack, check the screw holding your sear spring to the top tang. It doesn't look completely seated and the sear spring will definitely change the position of your sear when properly seated. When the triggers are set, and you trip the rear trigger, does the knock off jump up and hit the sear at all? Does it jump up and go past the end of the sear? I had the same problem a few months ago with a set of triggers made by an unknown that I bought from Joe do and had to have the end of my MVA sear tig welded to add length.


	IP Logged

westerner Frequent Elocutionist Offline deleted posts and threads record holder. Posts: 12043 Location: Why, out West of course Joined: May 29^th, 2006	Re: Any High Wall Zettler triggers out there? Reply #12 - Nov 29^th, 2025 at 11:09am	Print Post
	bpjack wrote on Nov 28^th, 2025 at 9:02pm: I just in charge of collecting 2 each of all the slugs native to the northwest. This one would make you proud.

	A blind squirrel runs into a tree every once in a while.
	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3514 Location: East Olympia, WA Joined: May 18^th, 2008	Re: Any High Wall Zettler triggers out there? Reply #13 - Nov 29^th, 2025 at 12:49pm	Print Post
	Yum. Throw it on the BBQ and slap it on a bun with some mustard and sauerkraut. Then toss it in the trash.

	ASSRA # 11318 Experience is something you don't get until just after you need it.
	IP Logged

gunlaker Frequent Elocutionist Offline Posts: 2493 Location: lower mainland, B.C. Joined: Dec 13^th, 2010	Re: Any High Wall Zettler triggers out there? Reply #14 - Nov 29^th, 2025 at 1:31pm	Print Post
	From what I've read, these were eaten by some German folks. I hope none of my relatives. I believe you get rid of the insides and fry up the delicious outer part. Chris


	IP Logged

Page Index Toggle

Pages: [1] 2 3

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.8772 seconds.