ASSRA Forum › General › Gunsmithing Single Shot Rifles › Daniel Fraser Armi San Marco
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Daniel Fraser Armi San Marco (Read 330 times)
John Robert
Participating Member
*
Offline



Posts: 43
Joined: Sep 8th, 2015
Daniel Fraser Armi San Marco
Feb 13th, 2025 at 9:07pm
Print Post  
Does anyone know what size and pitch of threads were used on the barrel threads of these little rifles , have a friend who is wanting to rebarrel one , trying to gain some info before diving in . My research thus far indicates that Frank Dehaas covered this rifle in his book A Potpourri of Single Shot Rifles and Actions , but I do not have a copy on hand . Any help greatly appreciated. JR
  
Back to top
 
IP Logged
 
oneatatime
Frequent Elocutionist
*****
Offline



Posts: 3968
Location: Rocky Mountains
Joined: Oct 30th, 2011
Re: Daniel Fraser Armi San Marco
Reply #1 - Feb 14th, 2025 at 12:32am
Print Post  
Is this the same one that is covered up in the "Important Topics" above under "Fraser Highlander"?
  
Back to top
 
IP Logged
 
MartiniBelgian
Frequent Elocutionist
*****
Offline



Posts: 1700
Location: Aarschot
Joined: Jun 7th, 2004
Re: Daniel Fraser Armi San Marco
Reply #2 - Feb 14th, 2025 at 2:37am
Print Post  
John Robert wrote on Feb 13th, 2025 at 9:07pm:
Does anyone know what size and pitch of threads were used on the barrel threads of these little rifles , have a friend who is wanting to rebarrel one , trying to gain some info before diving in . My research thus far indicates that Frank Dehaas covered this rifle in his book A Potpourri of Single Shot Rifles and Actions , but I do not have a copy on hand . Any help greatly appreciated. JR


Well, if you read that article, you will advise him to find another project...  Nothing to do with Daniel Fraser, not in design, not in quality of execution.
  
Back to top
WWW  
IP Logged
 
Jdhasty
Newbie
*
Offline



Posts: 7
Joined: Feb 23rd, 2022
Re: Daniel Fraser Armi San Marco
Reply #3 - Feb 17th, 2025 at 11:48pm
Print Post  
MartiniBelgian wrote on Feb 14th, 2025 at 2:37am:
John Robert wrote on Feb 13th, 2025 at 9:07pm:
Does anyone know what size and pitch of threads were used on the barrel threads of these little rifles , have a friend who is wanting to rebarrel one , trying to gain some info before diving in . My research thus far indicates that Frank Dehaas covered this rifle in his book A Potpourri of Single Shot Rifles and Actions , but I do not have a copy on hand . Any help greatly appreciated. JR


Well, if you read that article, you will advise him to find another project...  Nothing to do with Daniel Fraser, not in design, not in quality of execution.


One of the worthless pieces of junk resides not far from where I sit.  Way too much time and effort has been invested wasted in trying to make it even marginally serviceable.  
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.7869 seconds.