ASSRA Forum › General › For Sale/Trade › 44-77 brass wanted
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic 44-77 brass wanted (Read 399 times)
rollingblock
Senior Forum Member
****
Offline



Posts: 383
Location: Texas part of New Mexico
Joined: Aug 19th, 2012
44-77 brass wanted
Sep 8th, 2024 at 2:55pm
Print Post  
Looking for 44-77 Sharps brass with the “.085 rim thickness for an original Remington sporting rifle, or .43 Spanish with the thicker rim.

Also looking for a die set for the 44-77 (and please no “Capt. Obvious” replies), no one has them in stock and I don’t want to wait 8 months or longer. For now I’ll use my .43 Spanish die set with a .446 expander.

Thank’s in advance - John
  
Back to top
 
IP Logged
 
Oleblacksmith
Newbie
*
Offline



Posts: 0
Joined: Jan 10th, 2024
Re: 44-77 brass wanted
Reply #1 - Sep 8th, 2024 at 5:24pm
Print Post  
Check out Rocky Mountain Cartridge Co. Since I'm a Newbie I can't post their website.
  
Back to top
 
IP Logged
 
.22-5-40
Oldtimer
*****
Offline



Posts: 790
Joined: Feb 13th, 2010
Re: 44-77 brass wanted
Reply #2 - Sep 8th, 2024 at 7:41pm
Print Post  
Track Of The Wolf has .43 Spanish...it fit my original .44-77 Sharps.
Rim is .087".
« Last Edit: Sep 8th, 2024 at 7:55pm by .22-5-40 »  
Back to top
 
IP Logged
 
TN Longhunter
Participating Member
*
Offline



Posts: 13
Location: Tennessee
Joined: Jan 15th, 2014
Re: 44-77 brass wanted
Reply #3 - Sep 8th, 2024 at 8:09pm
Print Post  
Track of the Wolf as stated ($4 per case).Plus, just keep this thread going. I was in the same boat last year after going 44/77 free to three rollers and one Sharps in it. It is out there, just keep posting to different groups.
  
Back to top
 
IP Logged
 
Ranch13
Oldtimer
*****
Offline



Posts: 539
Location: East Central Wy.
Joined: Jan 20th, 2018
Re: 44-77 brass wanted
Reply #4 - Sep 9th, 2024 at 11:27am
Print Post  
Check the Buffalo Arms website to see what they might have on hand, and place a back order if they're out.

As far as dies go I've been using lee 43 mauser dies for the 44-77 for over a decade with good results. You will need a compression die if you load black powder.

Rocky Mountain Cartridge in Worland Wy does a good job with 44-77 brass .
  
Back to top
 
IP Logged
 
TN Longhunter
Participating Member
*
Offline



Posts: 13
Location: Tennessee
Joined: Jan 15th, 2014
Re: 44-77 brass wanted
Reply #5 - Sep 11th, 2024 at 9:36am
Print Post  
No “Cap Obvious “ answer but I call C&H about a set on backorder and they stated they were in the system and waiting for them to get back from heat treat. Said 8-10 weeks, I should have them.
  
Back to top
 
IP Logged
 
rollingblock
Senior Forum Member
****
Offline



Posts: 383
Location: Texas part of New Mexico
Joined: Aug 19th, 2012
Re: 44-77 brass wanted
Reply #6 - Sep 12th, 2024 at 9:55pm
Print Post  
TN Longhunter wrote on Sep 11th, 2024 at 9:36am:
No “Cap Obvious “ answer but I call C&H about a set on backorder and they stated they were in the system and waiting for them to get back from heat treat. Said 8-10 weeks, I should have them.

Thanks TN Longhunter, when I called them a couple of weeks ago I was told the same. Good luck and post when you get yours.


  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.5904 seconds.