ASSRA Forum - Smokeless powder for 38-50 Rem-Hep

ASSRA Forum › General › Reloading the Single Shot Rifle › Smokeless powder for 38-50 Rem-Hep

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: [1] 2

Hot Topic (More than 10 Replies)

Smokeless powder for 38-50 Rem-Hep (Read 2791 times)

WVsmoke Participating Member Offline Posts: 34 Location: West Virginia Joined: Feb 17^th, 2023	Smokeless powder for 38-50 Rem-Hep Aug 8^th, 2024 at 6:20pm	Print Post
	What powders are recommended for shooting the 38-50? I would like to hunt whitetails with a jacketed bullet in my rifle and I would like to know what powders work in large volume black powder cartridges? Allan


	IP Logged

craigster Oldtimer Online Posts: 758 Location: lost coast CA Joined: Feb 20^th, 2011	Re: Smokeless powder for 38-50 Rem-Hep Reply #1 - Aug 8^th, 2024 at 6:38pm	Print Post
	5744. Or Trail Boss.


	IP Logged

WVsmoke Participating Member Offline Posts: 34 Location: West Virginia Joined: Feb 17^th, 2023	Re: Smokeless powder for 38-50 Rem-Hep Reply #2 - Aug 8^th, 2024 at 8:40pm	Print Post
	Are either readily available today? Forgive my ignorance please, I don’t think I have loaded in quite some time…. Thanks, Allan


	IP Logged

craigster Oldtimer Online Posts: 758 Location: lost coast CA Joined: Feb 20^th, 2011	Re: Smokeless powder for 38-50 Rem-Hep Reply #3 - Aug 8^th, 2024 at 8:45pm	Print Post
	You'll just have to see what's out there in your local area.


	IP Logged

WVsmoke Participating Member Offline Posts: 34 Location: West Virginia Joined: Feb 17^th, 2023	Re: Smokeless powder for 38-50 Rem-Hep Reply #4 - Aug 8^th, 2024 at 9:18pm	Print Post
	Thanks, I will. Allan


	IP Logged

WVsmoke Participating Member Offline Posts: 34 Location: West Virginia Joined: Feb 17^th, 2023	Re: Smokeless powder for 38-50 Rem-Hep Reply #5 - Aug 8^th, 2024 at 10:04pm	Print Post
	The big suppliers on the internet seem to be out. I will keep an eye out for Accurate 5744 when I am out and about. I do have IMR 4198 and Accurate 2015 which both seem to be recommended for 45-70. I will have to search my loading tables for these two powders. Allan


	IP Logged

beltfed Frequent Elocutionist Offline Posts: 1796 Location: Central Wi Joined: Dec 20^th, 2007	Re: Smokeless powder for 38-50 Rem-Hep Reply #6 - Aug 9^th, 2024 at 9:33am	Print Post
	I suggest you look at smokeless 38-55 and 375Win loads in the handbooks, LYman #50 . You can work up in your (Modern, I hope) rifle with the 38-50 which has about 10% greater case capacity over the 38-55 . I found an excellent deer hunt load for my Marlin 336CB 38-55 with Reloader 7. Similar in burn rate to old IMR 3031which was and is a go-to for relatively straight wall cases. I had also used the 3031 for full loads in my '86 Win 45-70. Then graduated to 4895 or Varget when I ran out of 3031 beltfed/arnie


	IP Logged

WVsmoke Participating Member Offline Posts: 34 Location: West Virginia Joined: Feb 17^th, 2023	Re: Smokeless powder for 38-50 Rem-Hep Reply #7 - Aug 9^th, 2024 at 9:54am	Print Post
	Thanks beltfed, I will check out those resources. My IMR 3031 is my lightest container, indicating how popular it was 25 years ago in my reloading room. Allan


	IP Logged

Cbashooter Frequent Elocutionist Offline Posts: 1604 Location: Eastern Wa. Joined: Mar 31^st, 2018	Re: Smokeless powder for 38-50 Rem-Hep Reply #8 - Aug 9^th, 2024 at 9:32pm	Print Post
	here u go,from 1967 Ken Waters in Shooting Times


	IP Logged

WVsmoke Participating Member Offline Posts: 34 Location: West Virginia Joined: Feb 17^th, 2023	Re: Smokeless powder for 38-50 Rem-Hep Reply #9 - Aug 10^th, 2024 at 10:15am	Print Post
	Thanks Cbashooter.


	IP Logged

oneatatime Frequent Elocutionist Offline Posts: 4155 Location: Rocky Mountains Joined: Oct 30^th, 2011	Re: Smokeless powder for 38-50 Rem-Hep Reply #10 - Aug 10^th, 2024 at 7:03pm	Print Post
	WV, at the velocities involved the deer will never know whether the bullet had a jacket or not.


	IP Logged

WVsmoke Participating Member Offline Posts: 34 Location: West Virginia Joined: Feb 17^th, 2023	Re: Smokeless powder for 38-50 Rem-Hep Reply #11 - Aug 10^th, 2024 at 7:52pm	Print Post
	Well……. The way I learned to reload ammo, oneatatime, one uses jacketed bullets with white powder and greased grooved bullets with black powder…. I guess I was not brought up right?? Allan


	IP Logged

oneatatime Frequent Elocutionist Offline Posts: 4155 Location: Rocky Mountains Joined: Oct 30^th, 2011	Re: Smokeless powder for 38-50 Rem-Hep Reply #12 - Aug 10^th, 2024 at 8:38pm	Print Post
	If you were brought up in West Virginia I'm sure you were brought up right! I suppose Ken Waters wasn't though as every load on that page was white powder and lead bullets - OK, 3 of them had gas checks and 1 was a half jacket;-) I was just making a comment on the deer's reaction to being shot. Let's go at it a different way: what rifle do you have? What bullet were you thinking of using? What is the groove diameter of your barrel?
	« Last Edit: Aug 11^th, 2024 at 1:33am by oneatatime »

	IP Logged

argie1891 Senior Forum Member Offline Posts: 268 Location: selah, washington Joined: Jul 8^th, 2010	Re: Smokeless powder for 38-50 Rem-Hep Reply #13 - Aug 15^th, 2024 at 4:32am	Print Post
	i have been using 4198 and a cast bullet of 285 gr. in my rolling block. The charge weight is 23 gr. I would call it mostly a target load as if i remember correctly the velocity was fairly slow. Tomorrow i will check my records and see if i ran it over the chronograph. The one thing i can say it is accurate most loads going 1.5 inches with some right at an inch at 100 yards. Ken Waters lists 23 gr of 4198 in the 38-55 at 1450 fps with a 250 gr. bullet. that should be close to the 38/50 and if it does 1450 or so it should drop anything you hit with it. Waters lists 3 categories of rifles and this load is for his weakest action rifles. Hope this helps

	if you think you have it figured out then you just dont understand
	IP Logged

jhm Frequent Elocutionist Offline Posts: 1864 Location: georgia Joined: Sep 4^th, 2011	Re: Smokeless powder for 38-50 Rem-Hep Reply #14 - Aug 15^th, 2024 at 10:13pm	Print Post
	You know I am going to build me one of those if I can ever find a chamber reamer. Those things are like hens teeth. Tried two grind houses and both have unbelievable lead times. I am taking notes here so if I ever do get it done I will have some load info. JMH


	IP Logged

Page Index Toggle

Pages: [1] 2

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 1.3412 seconds.