ASSRA Forum › General › Gunsmithing Single Shot Rifles › Stevens 44 - is this strange?
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Stevens 44 - is this strange? (Read 1340 times)
Smoke
Oldtimer
*****
Offline



Posts: 881
Location: San Diego
Joined: Feb 24th, 2013
Stevens 44 - is this strange?
Sep 18th, 2023 at 4:39pm
Print Post  
I've never been inside a 44 Stevens before I got this one.  When I pull the lever and breech block I see the bushing shown in the pic.  It's pulled out of the lever so it'e more easily seen but fits flush when installed.

DeHaas' book says there's a screw through the lever at that point but doesn't mention the bushing.

This is the same rifle I asked about earlier with the custom double set triggers.   Is this another "custom" addition?  Or?

Speculations welcome.

Thanks

  
Inside every bright idea is the 50% probability of a disaster waiting to happen.
Back to top
 
IP Logged
 
Sure shot
Frequent Elocutionist
*****
Offline



Posts: 1226
Location: East central Iowa
Joined: Jun 22nd, 2020
Re: Stevens 44 - is this strange?
Reply #1 - Sep 18th, 2023 at 5:00pm
Print Post  
The early model 44's used screws for the lever and breech block.  The later models used a pin that Stevens called a pivot with a retaining screw on the right side of the frame. 
Your rifle looks absolutely correct from the factory.  It is a little unusual that the lever bushing came out just by removing the lever and breech block assembly.
« Last Edit: Sep 18th, 2023 at 5:16pm by Sure shot »  
Back to top
 
IP Logged
 
bobw
Frequent Elocutionist
*****
Offline



Posts: 2219
Joined: Mar 19th, 2013
Re: Stevens 44 - is this strange?
Reply #2 - Sep 18th, 2023 at 6:56pm
Print Post  
No speculation needed.  The bushing is required to fill the hole.  The hole is the only way to machine for the extractor pocket and extractor clearance.  So, you could say if it has an extractor set in the lever and in that position it will have the bushing.  The bushing reduces the hole size back to the pin diameter. 
Bob
« Last Edit: Sep 18th, 2023 at 7:22pm by bobw »  
Back to top
 
IP Logged
 
jhm
Frequent Elocutionist
*****
Online



Posts: 2142
Location: georgia
Joined: Sep 4th, 2011
Re: Stevens 44 - is this strange?
Reply #3 - Sep 18th, 2023 at 7:13pm
Print Post  
I have had a few and always wondered about the bushing. Now I know. You learn something new every day...




JMH
  
Back to top
 
IP Logged
 
bobw
Frequent Elocutionist
*****
Offline



Posts: 2219
Joined: Mar 19th, 2013
Re: Stevens 44 - is this strange?
Reply #4 - Sep 18th, 2023 at 7:17pm
Print Post  
I bit more info on the bushing in Stevens guns.  These all have the 6 o'clock extractor.

1. is a favorite.

2. is a 44

3. is a 44 1/2
  
Back to top
 
IP Logged
 
Smoke
Oldtimer
*****
Offline



Posts: 881
Location: San Diego
Joined: Feb 24th, 2013
Re: Stevens 44 - is this strange?
Reply #5 - Sep 19th, 2023 at 10:51am
Print Post  
Interesting and enlightening.

Thank you all.
  
Inside every bright idea is the 50% probability of a disaster waiting to happen.
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.9789 seconds.