ASSRA Forum - Miroko High Wall 6.5 Creedmoor Accuracy Potential

ASSRA Forum › General › Single Shot Rifles › Miroko High Wall 6.5 Creedmoor Accuracy Potential

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1

Miroko High Wall 6.5 Creedmoor Accuracy Potential (Read 1773 times)

RubEric Participating Member Offline Posts: 20 Joined: Sep 12^th, 2006	Miroko High Wall 6.5 Creedmoor Accuracy Potential Feb 6^th, 2022 at 2:05pm	Print Post
	I have purchased a Miroko 1885 High Wall in 6.5 Creedmoor but do not yet have it in hand. What accuracy have you been enjoying with this rifle?? What is its potential? I have not yet bought reloading equipment for this caliber and I ask in order to determine what level/quality of reloading dies I should buy. TNX, Eric


	IP Logged

Bulseyetom Frequent Elocutionist Offline Posts: 1025 Location: Santa Maria, Ca Joined: Oct 31^st, 2010	Re: Miroko High Wall 6.5 Creedmoor Accuracy Potential Reply #1 - Feb 6^th, 2022 at 3:10pm	Print Post
	I don't have one of the newer HiWalls but have several of the Browning clones which are identical I would imagine. My 25-06 with a 26" octagon barrel is a true moa rifle, and the one I have in 300 H&H is almost as good. I would buy match quality brass if possible. I also think that quality bullets are called for unless this is to be a hunting rifle like mine are. I use regular full length sizing dies and seat with Vickerman in-line dies. Tom


	Twitter IP Logged

Marlene Senior Forum Member Offline Posts: 276 Joined: Oct 30^th, 2015	Re: Miroko High Wall 6.5 Creedmoor Accuracy Potential Reply #2 - Feb 12^th, 2022 at 11:02pm	Print Post
	expect a minute, but don't fall out of your chair if you luck into a half minute or better


	IP Logged

ISS Oldtimer Offline Posts: 570 Joined: Feb 24^th, 2013	Re: Miroko High Wall 6.5 Creedmoor Accuracy Potential Reply #3 - Feb 13^th, 2022 at 4:25pm	Print Post
	Is it worthy of Whidden dies? Rich


	IP Logged

gunlaker Frequent Elocutionist Offline Posts: 2601 Location: lower mainland, B.C. Joined: Dec 13^th, 2010	Re: Miroko High Wall 6.5 Creedmoor Accuracy Potential Reply #4 - Feb 18^th, 2022 at 9:59am	Print Post
	I would bet quite good. I once had a Miroku 1885 in .270 Winchester and it was a really good rifle. It did put ten shots into an inch at 100m. The rifle was likely better than that is I owned it well before I understood some of the subtleties of shooting really well. Chris.


	IP Logged

JLouis Frequent Elocutionist Offline Posts: 10625 Joined: Apr 8^th, 2009	Re: Miroko High Wall 6.5 Creedmoor Accuracy Potential Reply #5 - Feb 18^th, 2022 at 11:10am	Print Post
	An extremely popular cartridge these days and I would expect the accuracy to be excellent as well. As it is also a quite popular long range competition cartridge that demands the very best in accuracy.

	" It Is Better To Now Have Been A Has Been Than A Never Was Or A Wanna Be "
	IP Logged

CharleHunter Senior Forum Member Offline Posts: 371 Joined: Feb 8^th, 2019	Re: Miroko High Wall 6.5 Creedmoor Accuracy Potential Reply #6 - Feb 21^st, 2022 at 4:13am	Print Post
	The Creedmore seams to be one of those inherently accurate cartridges and I would expect exceptional results with some load development. A good set of Redding bushing dies (or similar) or some Wilson straight line dies with appropriate bushes would be the way to go. Plus there are some really good Factory loads available if you are not going to shoot it that much (may be better to spend on ammo than dies??). Whilst related to those evils bolt guns there is a really good series of articles/tests on Factory ammo by Cal Zant on preisionrifleblog.com.


	IP Logged

Marlene Senior Forum Member Offline Posts: 276 Joined: Oct 30^th, 2015	Re: Miroko High Wall 6.5 Creedmoor Accuracy Potential Reply #7 - Feb 25^th, 2022 at 9:59am	Print Post
	ISS wrote on Feb 13^th, 2022 at 4:25pm: Is it worthy of Whidden dies? Rich I'd do my load development neck sizing with the standard dies adjusted out before spending the long money on custom dies, but I'd think if the rifle is showing enough promise a single shot probably benefits from a custom FL die more than a bolt gun.


	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

Page completed in 0.5693 seconds.