ASSRA Forum › General › Gunsmithing Single Shot Rifles › Relineing a German Schuetzen
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Relineing a German Schuetzen (Read 1370 times)
yamoon
Frequent Elocutionist
*****
Offline


NRA Life, ASSRA , GGCA,
MCA

Posts: 1006
Location: Junction City Kansas
Joined: Feb 11th, 2012
Relineing a German Schuetzen
Sep 26th, 2021 at 1:10am
Print Post  
Can a 8.15x46r be relined to 22 lr, if so how. Most 22 liners are 5/16 or 3/8 OD. I have a Schuetzen with a poor bore. It fits so nice I would like to make it into a 22 lr and keep the original barrel. I was wondering if a smith could drill out the chamber, fit a steel plug then drill for a 22 liner. What do you think?
Thanks Mike
  
Back to top
 
IP Logged
 
Grumpy gumpy
Full Member
***
Offline



Posts: 214
Location: australia
Joined: Jul 6th, 2016
Re: Relineing a German Schuetzen
Reply #1 - Sep 26th, 2021 at 2:42am
Print Post  
You can fit a turned down stepped barrel blank to most barrels, a bit fiddly to turn down the non chamber part, as it is thin, but can be done. The stepped blank is then glued or soldered into the original barrel and the muzzle and chamber ends cleaned up and the new chamber cut
Gumpy
  
Back to top
 
IP Logged
 
singleshotsam
Oldtimer
*****
Offline



Posts: 594
Location: Silver City NM
Joined: Jan 15th, 2009
Re: Relineing a German Schuetzen
Reply #2 - Sep 26th, 2021 at 9:07am
Print Post  
T.J's makes a 22 rim fire liner in 1/2" diameter. I used one to line a 44 caliber barrel to 22 rim fire.
  
Back to top
 
IP Logged
 
yamoon
Frequent Elocutionist
*****
Offline


NRA Life, ASSRA , GGCA,
MCA

Posts: 1006
Location: Junction City Kansas
Joined: Feb 11th, 2012
Re: Relineing a German Schuetzen
Reply #3 - Sep 26th, 2021 at 11:17am
Print Post  
Does TJs have a web site?
Thanks Mike
  
Back to top
 
IP Logged
 
bobw
Frequent Elocutionist
*****
Offline



Posts: 2107
Location: NW, Iowa
Joined: Mar 19th, 2013
Re: Relineing a German Schuetzen
Reply #4 - Sep 26th, 2021 at 11:20am
Print Post  
Look at the important topics section at the top of this gunsmithing section.  A price list is there with contact info.
  
Robert Warren
Back to top
 
IP Logged
 
yamoon
Frequent Elocutionist
*****
Offline


NRA Life, ASSRA , GGCA,
MCA

Posts: 1006
Location: Junction City Kansas
Joined: Feb 11th, 2012
Re: Relineing a German Schuetzen
Reply #5 - Sep 26th, 2021 at 2:50pm
Print Post  
Recommendations for a gun smith to install a 1/2 TJs liner & alter the extractor. This old schuetzen was made when .250 berdan primers were used. The firing pin strikes several thousands low, no wear in the locking lugs (Stahl Martini), so a few thousands off the lugs to lower the block should bring the firing pin in line to fire a 22 rimfire.
Thanks Mike
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 1.3946 seconds.