ASSRA Forum - I need a drawing of Rem 1910 rolling block breech

ASSRA Forum › General › Gunsmithing Single Shot Rifles › I need a drawing of Rem 1910 rolling block breech

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1

I need a drawing of Rem 1910 rolling block breech (Read 2222 times)

Clark Participating Member Offline Posts: 20 Location: Mercer Island Joined: Aug 7^th, 2005	I need a drawing of Rem 1910 rolling block breech Aug 22^nd, 2021 at 12:06pm	Print Post
	I need to set the barrel back by a thread. I have a lathe and a mill.


	IP Logged

Chuckster Frequent Elocutionist Offline Posts: 2311 Location: Colorado Joined: May 15^th, 2008	Re: I need a drawing of Rem 1910 rolling block breech Reply #1 - Aug 23^rd, 2021 at 10:28pm	Print Post
	Clark, The ASSRA Archives has drawings for a Remington Rolling Block. No idea if it is exactly like yours, (You need to *Login* or *Register* to view media files and links); Chuck


	IP Logged

oughtsix Global Moderator ASSRA Board Member Offline Posts: 1361 Location: Columbus Joined: May 31^st, 2009	Re: I need a drawing of Rem 1910 rolling block breech Reply #2 - Aug 24^th, 2021 at 7:46am	Print Post
	if a schematic helps (You need to *Login* or *Register* to view media files and links)

	Life Member ASSRA, OGCA & TSGC I'm all in favor of keeping dangerous weapons out the hands of fools. Let's start with typewriters........ Frank Lloyd Wright
	IP Logged

Tom_Trevor assra life no.71 Oldtimer Offline Tom Trevor Posts: 712 Location: Granada Hills Ca. Joined: Jun 16^th, 2004	Re: I need a drawing of Rem 1910 rolling block breech Reply #3 - Aug 24^th, 2021 at 4:12pm	Print Post
	Single Shot Rifles and Actions Frank De Haas pages 328-329.


	IP Logged

Clark Participating Member Offline Posts: 20 Location: Mercer Island Joined: Aug 7^th, 2005	Re: I need a drawing of Rem 1910 rolling block breech Reply #4 - Aug 25^th, 2021 at 3:44pm	Print Post
	De Haas shows a drawing that matches the 38 special barrel breech. It as a No.1 7mmMauser 1879 Argentine


	IP Logged

Clark Participating Member Offline Posts: 20 Location: Mercer Island Joined: Aug 7^th, 2005	Re: I need a drawing of Rem 1910 rolling block breech Reply #5 - Aug 26^th, 2021 at 12:42am	Print Post
	I think it is an 1879 No 1


	IP Logged

Clark Participating Member Offline Posts: 20 Location: Mercer Island Joined: Aug 7^th, 2005	Re: I need a drawing of Rem 1910 rolling block breech Reply #6 - Aug 26^th, 2021 at 12:43am	Print Post
	I made this drawing


	IP Logged

Clark Participating Member Offline Posts: 20 Location: Mercer Island Joined: Aug 7^th, 2005	Re: I need a drawing of Rem 1910 rolling block breech Reply #7 - Aug 28^th, 2021 at 12:35pm	Print Post
	Putting round height gauges [they look like washers] in the action with the hammer and block installed, I can measure shoulder to breech face with a 1" depth micrometer. It is as best I can measure, 1.372". This is different from the 1.4" barrel I took out. This is different from the 1.43" De Haas drawing. The receiver face has been trued, but that is only 0.009" deep and cannot account for the above discrepancies.
	« Last Edit: Aug 28^th, 2021 at 12:44pm by Clark »

	IP Logged

porchdog48 Full Member Offline Posts: 106 Location: Waynesburg, Ohio Joined: Mar 25^th, 2010	Re: I need a drawing of Rem 1910 rolling block breech Reply #8 - Aug 29^th, 2021 at 6:51pm	Print Post
	Sent you a PM. Dave


	IP Logged

Clark Participating Member Offline Posts: 20 Location: Mercer Island Joined: Aug 7^th, 2005	Re: I need a drawing of Rem 1910 rolling block breech Reply #9 - Aug 30^th, 2021 at 11:07pm	Print Post
	I got it running tonight with the barrel set back a thread. (You need to *Login* or *Register* to view media files and links)


	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›