(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Short neck (Read 1436 times)
yamoon
Oldtimer
*****
Offline


NRA Life, ASSRA , GGCA,
MCA

Posts: 964
Location: Junction City Kansas
Joined: Feb 11th, 2012
Short neck
Jun 14th, 2021 at 12:20pm
Print Post  
Hello
I have sent hundreds of pounds of lead down range in 50 years, breach seated and stop ring. I need to load lubed bullet fixed ammo & don’t have a lot of experience. How to prevent powder from sticking to the lube when the case has a short neck and the bullet extends into the case? Use a bit of tissue or other material? Should I worry about chamber ringing? Can you more experienced guys suggest a material to secure the powder next to the primer? I wish to use 2400 & 4227.
Thanks for any suggestions.
Mike
  
Back to top
 
IP Logged
 
calledflyer
Frequent Elocutionist
*****
Offline



Posts: 3852
Joined: Mar 9th, 2015
Re: Short neck
Reply #1 - Jun 14th, 2021 at 2:03pm
Print Post  
just load 'em up (safely) and they'll be fine.
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 17434
Location: Oregon
Joined: Feb 2nd, 2009
Re: Short neck
Reply #2 - Jun 14th, 2021 at 2:25pm
Print Post  
Never did anything special to keep powder away from the base of the bullets in almost 50 years of loading fixed ammo.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
jfeldman
ASSRA Board Member
*****
Offline



Posts: 1099
Location: Imperial Beach, Ca
Joined: Nov 5th, 2005
Re: Short neck
Reply #3 - Jun 14th, 2021 at 2:27pm
Print Post  
Mike, I use that green floral foam cut into 1/4 inch sheets. Press it over the case mouth and seat the bullet on top of it.  My understanding of chamber ringing is that you don't want a wad holding the charge against the primer.

Regards,
Joe
  
Back to top
 
IP Logged
 
rkba2nd
Frequent Elocutionist
*****
Offline



Posts: 2057
Location: earth
Joined: Feb 16th, 2009
Re: Short neck
Reply #4 - Jun 14th, 2021 at 4:05pm
Print Post  
Like Marlinguy, have been reloading for over 60 years and have never found a need, and then only to tip muzzle up to settle the powder in the base of the case when breech seating and shooting offhand, or tipping the case when shooting from a bench.  No experience with black powder, other than percussion rifles and handguns, and don't feel the need at this point to start.
Some top tier shooters will respond, and they may/will have different ideas.
  
rkba2nd
Back to top
 
IP Logged
 
westerner
Frequent Elocutionist
*****
Offline


deleted posts and threads
record holder.

Posts: 12066
Location: Why, out West of course
Joined: May 29th, 2006
Re: Short neck
Reply #5 - Jun 14th, 2021 at 6:19pm
Print Post  
I've never shot a cast lead bullet that extended below the neck into the case. 
I would avoid that. 

Load a shorter bullet or throat the bore to suit your bullets length. 

  
A blind squirrel runs into a tree every once in a while.
Back to top
 
IP Logged
 
Cbashooter
Frequent Elocutionist
*****
Offline



Posts: 1608
Location: Eastern Wa.
Joined: Mar 31st, 2018
Re: Short neck
Reply #6 - Jun 14th, 2021 at 6:37pm
Print Post  
I've loaded 1000s of the 311284 in fixed ammo in 30-06.the GC is often below the neck and sometimes a bit if the last band.
I never used fillers.accuracy always good.
  
Back to top
 
IP Logged
 
rkba2nd
Frequent Elocutionist
*****
Offline



Posts: 2057
Location: earth
Joined: Feb 16th, 2009
Re: Short neck
Reply #7 - Jun 15th, 2021 at 12:35am
Print Post  
Sound advice from westerner even when using jacketed bullets. I missed the fact that your cast bullets were being seated below the neck, pretty obvious from your heading. Mind was on a lunch break!!!  Either solution to the problem is fairly simple to accomplish, obviously a shorter bullet the easier of the two.
  
rkba2nd
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.7820 seconds.