ASSRA Forum - breech seater for a CPA in 32-40

ASSRA Forum › General › Reloading the Single Shot Rifle › breech seater for a CPA in 32-40

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1 [2]

breech seater for a CPA in 32-40 (Read 7668 times)

JLouis Frequent Elocutionist Offline Posts: 10625 Joined: Apr 8^th, 2009	Re: breech seater for a CPA in 32-40 Reply #15 - Sep 7^th, 2020 at 12:08pm	Print Post
	Might also try: Breech seaters for High/low walls, Hepburns, Rugers, others. Steven Durren 1170 Auborne Rd. Adrian, MI 49221 517-264-0528 sdurren1(at)comcast.net (You need to *Login* or *Register* to view media files and links)

	" It Is Better To Now Have Been A Has Been Than A Never Was Or A Wanna Be "
	IP Logged

Cbashooter Frequent Elocutionist Offline Posts: 1570 Location: Eastern Wa. Joined: Mar 31^st, 2018	Re: breech seater for a CPA in 32-40 Reply #16 - Sep 7^th, 2020 at 3:20pm	Print Post
	Dellet wrote on Sep 7^th, 2020 at 12:30am: This is a reasonable solution for a bullet seater can be made by using a fired case and drilling out the primer pocket to allow a short cleaning rod to pass through. Then file off the needle of a cleaning jag and screw it on just like if using a case for a bore guide. This generally allows enough force to start the bullet enough to use a plugged case even if the bullet is not tapered. If using a tapered or soft enough bullet, a stop ring type collet can be added. A slight bend in the rod clears the hammer. I have also enlarge the primer pocket enough on a filled case type plugged seater to accept a cleaning rod with a rounded tip to push the case. Works pretty well on Model 44’s where the block doesn’t roll forward. I use a plug case in my model 44 and the breach does tip forward a bit


	IP Logged

westerner Frequent Elocutionist Offline deleted posts and threads record holder. Posts: 11462 Location: Why, out West of course Joined: May 29^th, 2006	Re: breech seater for a CPA in 32-40 Reply #17 - Sep 8^th, 2020 at 2:37am	Print Post
	Would it be cheaper and easier to get a mold that casts the correct size bullet? Just a thought.

	A blind squirrel runs into a tree every once in a while.
	IP Logged

jagfolks Junior Member Offline Posts: 61 Location: Plymouth, Mi. Joined: Dec 16^th, 2010	Re: breech seater for a CPA in 32-40 Reply #18 - Sep 8^th, 2020 at 10:06am	Print Post
	Dave Bennett's 200 gr .321 bullets breech seat easily with a plugged case in my CPA rifle.


	IP Logged

GT Frequent Elocutionist Online Posts: 2040 Location: Northeast Wyoming Joined: Jun 28^th, 2015	Re: breech seater for a CPA in 32-40 Reply #19 - Sep 8^th, 2020 at 6:20pm	Print Post
	Rap, Check your PM's Greg

	"To invent, you need a good imagination and a pile of junk" T. A. Edison "The trouble ain't that there is too many fools, but that the lightning ain't distributed right" M.T.
	IP Logged

JLouis Frequent Elocutionist Offline Posts: 10625 Joined: Apr 8^th, 2009	Re: breech seater for a CPA in 32-40 Reply #20 - Sep 8^th, 2020 at 6:36pm	Print Post
	You can also make yourself a seater and an adjustable seater case that simply works off of a tang sight base cross attachment screw as being shown below. The piece beyond the seater case is just a Delrin plug to protect the mouth of the case when it is being stored. Its actually really simple to make and the bend in the handle is just to allow it to clear the scope. (You need to *Login* or *Register* to view media files and links) (You need to *Login* or *Register* to view media files and links)

	" It Is Better To Now Have Been A Has Been Than A Never Was Or A Wanna Be "
	IP Logged

Pages: 1 [2]

‹ Previous Topic | Next Topic ›

Page completed in 1.1207 seconds.