(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: [1] 2 3  Send TopicPrint
Very Hot Topic (More than 25 Replies) 44-77 (Read 8327 times)
Hiwall55
Senior Forum Member
****
Offline



Posts: 468
Location: west central Illinois
Joined: Jun 30th, 2012
44-77
Jul 17th, 2019 at 2:01pm
Print Post  
Anyone  make  any 44-77 's from what parent case?
348 is too short ,so 50-110 Winchester? Any help would be appreciated.
  
Back to top
 
IP Logged
 
nuclearcricket
Oldtimer
*****
Offline



Posts: 824
Joined: Oct 15th, 2008
Re: 44-77
Reply #1 - Jul 17th, 2019 at 2:30pm
Print Post  
Baco makes their 44-77 cases from the 348. The 50-110 is actually the parent case for the 348 but it was beefed up to contain the pressure of the smokeless loads. IMHO the 110 case would be a bit better to use to form 44-77 from as it would give you a bit more internal capacity, not that you really need any extra room in there. I know that with my fire formed Jamison brass I can easily drop 79 gr of Swiss 1.5 to the base of the neck. Lots of romp and stomp down range with a 480 gr gg bullet.
Sam
  
Back to top
 
IP Logged
 
Hiwall55
Senior Forum Member
****
Offline



Posts: 468
Location: west central Illinois
Joined: Jun 30th, 2012
Re: 44-77
Reply #2 - Jul 18th, 2019 at 6:02am
Print Post  
Thanks Sam. That's the info I was looking for.
  
Back to top
 
IP Logged
 
kensmachine
Oldtimer
*****
Offline



Posts: 574
Joined: Nov 21st, 2012
Re: 44-77
Reply #3 - Jul 18th, 2019 at 10:53am
Print Post  
348 is 2.25 long all the spec I see for 44-77/43 spanish is 2.25 long so why is it too short. next I have a old beat up 74 sharps I don't think the small rims of the 348/50-110 will work in my rifle Ken
  
Back to top
 
IP Logged
 
nuclearcricket
Oldtimer
*****
Offline



Posts: 824
Joined: Oct 15th, 2008
Re: 44-77
Reply #4 - Jul 18th, 2019 at 11:17am
Print Post  
Ken, the rim thickness of a standard 348 case is about .064-.065. If your rim recess is cut deeper than that, BACO reforms the rims for the deeper rim cut.The rims end up looking a lot like Betrum 43 mauser cases and they may need to be set up and the thickness trimed down a wee bit. I have one of those reformed cases, I got it by accident and honestly I wasn't impressed with it. yes it would work but may need tinnkered with just a bit.  I have been lucky in that I have been able to pick up a good supply of 44-77 brass and I am keeping it all. It would be nice if someone would set up and make a run of it. I am sure it would not set on the slelves of the right dealers very long.
Sam
  
Back to top
 
IP Logged
 
kensmachine
Oldtimer
*****
Offline



Posts: 574
Joined: Nov 21st, 2012
Re: 44-77
Reply #5 - Jul 18th, 2019 at 11:40am
Print Post  
I have 20 of the BACO 44-77 with the reformed head. with the small head diameter im my rifle I think the extractor wouldn't extract the case I may need to get a new extractor. ken
  
Back to top
 
IP Logged
 
Hiwall55
Senior Forum Member
****
Offline



Posts: 468
Location: west central Illinois
Joined: Jun 30th, 2012
Re: 44-77
Reply #6 - Jul 18th, 2019 at 1:20pm
Print Post  
Ken when you fireform  a 33 caliber in a 44 caliber you will be at least .050 short.
  
Back to top
 
IP Logged
 
OLD TUCK
Senior Forum Member
****
Offline



Posts: 469
Location: Middleborough MA
Joined: Oct 5th, 2017
Re: 44-77
Reply #7 - Jul 18th, 2019 at 2:48pm
Print Post  
I have a friend that owns or used to own a 44-77. He used if my memory is correct a .43 Spanish with the "A" base. they worked well for him. Reformed nice, not a lot and shot very well. He has not Shot for quite a while so do not  know if he still owns the Rifle. It was a Ballard with a replaced Barrel. HTH
Regards, FITZ. OLD TUCK Smiley
  
Back to top
 
IP Logged
 
Hiwall55
Senior Forum Member
****
Offline



Posts: 468
Location: west central Illinois
Joined: Jun 30th, 2012
Re: 44-77
Reply #8 - Jul 18th, 2019 at 9:40pm
Print Post  
Picked up 6 50-110 cases when I got 100 loaded 44-77's with brand new  Jamison brass.
Thanks for the replies.
Bill
  
Back to top
 
IP Logged
 
Yellowhouse
Full Member
***
Offline



Posts: 155
Location: Oklahoma
Joined: Mar 31st, 2008
Re: 44-77
Reply #9 - Jul 19th, 2019 at 9:35pm
Print Post  
I have a few BACO reformed .348 and they work pretty good in a Shiloh.  This brass has the head reworked and then is stretched to 2.25.
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 18069
Location: Oregon
Joined: Feb 2nd, 2009
Re: 44-77
Reply #10 - Jul 21st, 2019 at 10:39am
Print Post  
All my cases are .43 Mauser, but they're tough to find these days too. I bought a bunch of loaded .43 Mauser from an estate sale and pulled bullets. Then trimmed and resized them for my Roller. But I also had to thin the rims slightly as they were too thick to allow the block to fully close.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Hiwall55
Senior Forum Member
****
Offline



Posts: 468
Location: west central Illinois
Joined: Jun 30th, 2012
Re: 44-77
Reply #11 - Jul 22nd, 2019 at 2:16am
Print Post  
Thanks Vall,I will be on the lookout for  those cases too. Not a problem to do the work to modify them.
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 18069
Location: Oregon
Joined: Feb 2nd, 2009
Re: 44-77
Reply #12 - Jul 22nd, 2019 at 10:38am
Print Post  
They were easy to modify. I found they had deeper primer pockets and that made thinning the rims even easier. Chucked them in the lathe and turned the headstamp off to get them thinner. After that they fit, and primers were flush too.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
OLD TUCK
Senior Forum Member
****
Offline



Posts: 469
Location: Middleborough MA
Joined: Oct 5th, 2017
Re: 44-77
Reply #13 - Jul 22nd, 2019 at 3:53pm
Print Post  
Yea Vall, you brought back my Memory. The guy I knew was using .43 Mauser. He had a bit of a Headspace problem. He made a Die and punch and set up in a Arbor press and put them in and gave it a good press and made an "A" base head with a .01 proud step to take up the excess Head Space. He shot it a lot as it was a very nice rifle. I was always bothered though thinking about the step and wondering what that had done to the Case Head strength.
HTH regards, FITZ. OLD TUCK Smiley
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 18069
Location: Oregon
Joined: Feb 2nd, 2009
Re: 44-77
Reply #14 - Jul 22nd, 2019 at 11:31pm
Print Post  
OLD TUCK wrote on Jul 22nd, 2019 at 3:53pm:
Yea Vall, you brought back my Memory. The guy I knew was using .43 Mauser. He had a bit of a Headspace problem. He made a Die and punch and set up in a Arbor press and put them in and gave it a good press and made an "A" base head with a .01 proud step to take up the excess Head Space. He shot it a lot as it was a very nice rifle. I was always bothered though thinking about the step and wondering what that had done to the Case Head strength.
HTH regards, FITZ. OLD TUCK Smiley


Mine was the opposite issue on my original Remington #1 Sporter Fitz. Too thick a rim, so more headspace was needed, and thus a thinner rim.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Page Index Toggle Pages: [1] 2 3 
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 1.2994 seconds.