ASSRA Forum - 32-40 mold suggestions

ASSRA Forum › General › Reloading the Single Shot Rifle › 32-40 mold suggestions

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Hot Topic (More than 10 Replies)

32-40 mold suggestions (Read 3604 times)

critter68 Senior Forum Member ASSRA Board Member Offline Posts: 293 Location: Wisconsin Joined: May 31^st, 2018	32-40 mold suggestions Jan 9^th, 2019 at 7:21pm	Print Post
	suggestions for molds from you guys. probably lean more towards a custom but again open to suggestions. Will be breech seating, schuetzen shooting, have shilen 14 twist barrel that slugs at .3177. thanks

	ASSRA LIFE#294 NRA LIFE #194353342
	IP Logged

frnkeore Frequent Elocutionist Offline Posts: 7658 Location: Central Point, OR 97502 Joined: Jun 16^th, 2010	Re: 32-40 mold suggestions Reply #1 - Jan 9^th, 2019 at 7:49pm	Print Post
	This NOE will do well in your barrel. It will be a little tight but, should shoot well. You can also run it through a .318 or .319 sizing die and it would be just right. (You need to *Login* or *Register* to view media files and links) Frank

	ASSRA Member #696, ISSA Member #339
	YIM AIM IP Logged

critter68 Senior Forum Member ASSRA Board Member Offline Posts: 293 Location: Wisconsin Joined: May 31^st, 2018	Re: 32-40 mold suggestions Reply #2 - Jan 9^th, 2019 at 8:22pm	Print Post
	I did not see that one so thanks frank. the .3177 has me a little stumped as everything is .321 or larger in bullet designs and manufacturers I had anticipated trying Not opposed to sizing just had not planned on it. Don't want to put a cheater bar extension on my weber seating tool

	ASSRA LIFE#294 NRA LIFE #194353342
	IP Logged

critter68 Senior Forum Member ASSRA Board Member Offline Posts: 293 Location: Wisconsin Joined: May 31^st, 2018	Re: 32-40 mold suggestions Reply #3 - Jan 9^th, 2019 at 8:38pm	Print Post
	only .318,.319 and .320 sizer dies I see are custom from baco at 48 bucks a pop. I have a rcbs lube/sizer

	ASSRA LIFE#294 NRA LIFE #194353342
	IP Logged

JLouis Frequent Elocutionist Offline Posts: 10625 Joined: Apr 8^th, 2009	Re: 32-40 mold suggestions Reply #4 - Jan 9^th, 2019 at 10:22pm	Print Post
	I would look at the scores in the match results section, pick all of the tops three shooters, send them PM's and then pick their Brains if you are real serious about receiving the very best of information and not just opinions.

	" It Is Better To Now Have Been A Has Been Than A Never Was Or A Wanna Be "
	IP Logged

Rebel Frequent Elocutionist Offline Posts: 4292 Location: Rockets and Race Cars Joined: Mar 9^th, 2015	Re: 32-40 mold suggestions Reply #5 - Jan 9^th, 2019 at 10:31pm	Print Post
	Good advice, J. Louis! Aaron

	WARNING: This post may contain material offensive to those who lack wit, humor, common sense and supporting factual or anecdotal evidence. Let's Go Sonny!
	IP Logged

jfeldman ASSRA Board Member Offline Posts: 1120 Location: Imperial Beach, Ca Joined: Nov 5^th, 2005	Re: 32-40 mold suggestions Reply #6 - Jan 9^th, 2019 at 11:04pm	Print Post
	With a 14 twist barrel, I would want to use a heavier bullet - maybe 215 grains or so? Maybe Schuetzendave will run some numbers on heavier bullets for you.......... Regards, Joe


	IP Logged

frnkeore Frequent Elocutionist Offline Posts: 7658 Location: Central Point, OR 97502 Joined: Jun 16^th, 2010	Re: 32-40 mold suggestions Reply #7 - Jan 10^th, 2019 at 1:02am	Print Post
	JLouis wrote on Jan 9^th, 2019 at 10:22pm: I would look at the scores in the match results section, pick all of the tops three shooters, send them PM's and then pick their Brains if you are real serious about receiving the very best of information and not just opinions. Well, I think French was one of the top 3 shooters in the Golden Age and that IS a copy of French's bullet. Frank

	ASSRA Member #696, ISSA Member #339
	YIM AIM IP Logged

almat Participating Member Offline Posts: 34 Joined: Sep 27^th, 2013	Re: 32-40 mold suggestions Reply #8 - Jan 10^th, 2019 at 2:13am	Print Post
	Check with Pioneer products. Fred Leeth they have some .318 200+grain molds. I dont believe theres a website call and request a list. Phone #937-839-4363


	IP Logged

critter68 Senior Forum Member ASSRA Board Member Offline Posts: 293 Location: Wisconsin Joined: May 31^st, 2018	Re: 32-40 mold suggestions Reply #9 - Jan 10^th, 2019 at 7:18am	Print Post
	What is Sg? and as the value decreases is that a good thing?

	ASSRA LIFE#294 NRA LIFE #194353342
	IP Logged

RSW Frequent Elocutionist Offline Posts: 1299 Location: Arizona Joined: Sep 8^th, 2006	Re: 32-40 mold suggestions Reply #10 - Jan 10^th, 2019 at 10:13am	Print Post
	critter68 If you end up needing to size your bullets a thou or so, you can pan lube them and size them with a push-through die. Lee Precision has dies at a reasonable price and they mount to your loading press. If their standard sizes don't meet you needs, they offer custom service to make a die to your specifications. I have used several and they all have been dead-on to my size specs and truly round. Good luck

	Randy W ASSRA 10211 - ISSA 125 There are indeed two Americas. Simply put, it is not the haves and have nots. The two Americans are in reality divided into those who do and those who don't.
	GTalk IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 1.3453 seconds.