Welcome, Guest. Please
Login
or
Register
ASSRA Home
Board Index
Help
Search
Login
Register
ASSRA Forum
›
General
›
Rifle Photos
› model 33 Husqvarna
(Moderator Group: Moderator)
‹
Previous Topic
|
Next Topic
›
Pages:
[1]
2
Send Topic
Print
model 33 Husqvarna (Read 5150 times)
Bonner
Full Member
Offline
Posts: 135
Location: middle georgia
Joined: Mar 2
nd
, 2015
model 33 Husqvarna
Aug 31
st
, 2018 at 1:40pm
Print Post
Here is one that followed me home from a auction, the guy call it a 6x39R?? the bore end is .325 dia. does any one know what the marking on the barrel mean?? Thank Bonner
IP Logged
Rebel
Frequent Elocutionist
Offline
Posts: 4292
Location: Rockets and Race Cars
Joined: Mar 9
th
, 2015
Re: model 33 Husqvarna
Reply #1 -
Aug 31
st
, 2018 at 2:45pm
Print Post
Nice rifle!
I need one,
Aaron
WARNING: This post may contain material offensive to those who lack wit, humor, common sense and supporting factual or anecdotal evidence. Let's Go Sonny!
IP Logged
marlinguy
Frequent Elocutionist
Offline
Ballards may be weaker,
but they sure are neater!
Posts: 15994
Location: Oregon
Joined: Feb 2
nd
, 2009
Re: model 33 Husqvarna
Reply #2 -
Aug 31
st
, 2018 at 3:16pm
Print Post
No, but I'd bet it's not a 6mm anything. Most are in either 9.3mm or 9.5mm, and the lengths can vary. You'll need to chamber cast it to ensure what caliber and groove diameter it really is. It might be the unusual 8.6mm, or that might mean it's an 8.6mm groove diameter.
Mine is a 9.5x51R and I use .38-55 brass shortened and a .375" bullet. Yours could be a 57, 62, or even longer case.
These are very neat guns, and fairly rare in the USA. There's 3 or 4 of us here at ASSRA who have them, and have been working up loads for them. Most were the 9.3 version if I recall.
«
Last Edit: Aug 31
st
, 2018 at 3:21pm by marlinguy
»
(You need to
Login
or
Register
to view media files and links)
IP Logged
marlinguy
Frequent Elocutionist
Offline
Ballards may be weaker,
but they sure are neater!
Posts: 15994
Location: Oregon
Joined: Feb 2
nd
, 2009
Re: model 33 Husqvarna
Reply #3 -
Aug 31
st
, 2018 at 3:22pm
Print Post
Here's some previous discussion:
(You need to
Login
or
Register
to view media files and links)
(You need to
Login
or
Register
to view media files and links)
IP Logged
oneatatime
Frequent Elocutionist
Offline
Posts: 3846
Location: Rocky Mountains
Joined: Oct 30
th
, 2011
Re: model 33 Husqvarna
Reply #4 -
Aug 31
st
, 2018 at 5:28pm
Print Post
With that groove diameter it sounds like one of the 8s that the 33 was chambered for - 8X42R, 8X57R/360. A chamber cast would be the first thing to do. Found this on the 8x42R:
"I think you first need to make a chamber cast... as I see different dimensions for the 8X42R case...
Ex;
Base; 0.488" to 0.467"
Rim dia; 0.5701" to 0.524"
Rim thickness; 0.055" to 0.049"
So, my choice would be to start with easy to get, inexpensive 7.62X54R cases as per CIP specs;
Base; 0.487" max / 0.483"
Rim dia; 0.570" max
Rim thickness; 0.063" max / 0.053" min
If you already have the dies, it would be pretty easy to try it.... the other case I'd try would be the .303 Brit.."
Of course if it is the 8x57R(360) the base case would be a 9.3x72R.
IP Logged
oneatatime
Frequent Elocutionist
Offline
Posts: 3846
Location: Rocky Mountains
Joined: Oct 30
th
, 2011
Re: model 33 Husqvarna
Reply #5 -
Aug 31
st
, 2018 at 5:44pm
Print Post
With that groove diameter it sounds like one of the 8s that the 33 was chambered for - 8X42R, 8X57R/360. A chamber cast would be the first thing to do. Found this on the 8x42R:
"I think you first need to make a chamber cast... as I see different dimensions for the 8X42R case...
Ex;
Base; 0.488" to 0.467"
Rim dia; 0.5701" to 0.524"
Rim thickness; 0.055" to 0.049"
So, my choice would be to start with easy to get, inexpensive 7.62X54R cases as per CIP specs;
Base; 0.487" max / 0.483"
Rim dia; 0.570" max
Rim thickness; 0.063" max / 0.053" min
If you already have the dies, it would be pretty easy to try it.... the other case I'd try would be the .303 Brit.."
Of course if it is the 8x57R(360) the base case would be a 9.3x72R.
IP Logged
oneatatime
Frequent Elocutionist
Offline
Posts: 3846
Location: Rocky Mountains
Joined: Oct 30
th
, 2011
Re: model 33 Husqvarna
Reply #6 -
Aug 31
st
, 2018 at 5:45pm
Print Post
Here's a Nowegian link with a pic of the 8x42R brass:
(You need to
Login
or
Register
to view media files and links)
IP Logged
svartkruttgris#369
Frequent Elocutionist
Offline
Posts: 2980
Location: Colorado, Norway, Sweden
Joined: Oct 28
th
, 2014
Re: model 33 Husqvarna
Reply #7 -
Aug 31
st
, 2018 at 7:24pm
Print Post
oneatatime wrote
on Aug 31
st
, 2018 at 5:45pm:
Here's a Nowegian link with a pic of the 8x42R brass:
(You need to
Login
or
Register
to view media files and links)
That is an interesting article. A bit humorous with a running discourse of Monopoly woven in with case measurements.
IP Logged
marlinguy
Frequent Elocutionist
Offline
Ballards may be weaker,
but they sure are neater!
Posts: 15994
Location: Oregon
Joined: Feb 2
nd
, 2009
Re: model 33 Husqvarna
Reply #8 -
Aug 31
st
, 2018 at 8:13pm
Print Post
I wonder if that ".325" bore measurement was slugging the bore, or just dial calipers in the end of the barrel?
(You need to
Login
or
Register
to view media files and links)
IP Logged
Bonner
Full Member
Offline
Posts: 135
Location: middle georgia
Joined: Mar 2
nd
, 2015
Re: model 33 Husqvarna
Reply #9 -
Aug 31
st
, 2018 at 8:34pm
Print Post
es, Just dial calipers in the end of the bore. A fix round of 38-55 will chamber with no problem, I have not made a chamber cast but i will put the information here. A couple more shot's of the marking. Thanks for any help, Bonner
IP Logged
marlinguy
Frequent Elocutionist
Offline
Ballards may be weaker,
but they sure are neater!
Posts: 15994
Location: Oregon
Joined: Feb 2
nd
, 2009
Re: model 33 Husqvarna
Reply #10 -
Sep 1
st
, 2018 at 10:25am
Print Post
A half stock version too! Most I've seen were full stocked forearms. Pretty neat rifle!
Guessing the bore will be a fair bit larger groove than the .325" given by dial calipers.
(You need to
Login
or
Register
to view media files and links)
IP Logged
Fazer
Full Member
Offline
Posts: 248
Joined: Jun 9
th
, 2010
Re: model 33 Husqvarna
Reply #11 -
Sep 1
st
, 2018 at 12:21pm
Print Post
One of mine is 9.3X57R, same as English 360, 2 1/4. I got it at an auction. It was listed as 9.3X57 cal in the guide. No R. Big difference.
I knew what I was looking at but there were others that didn't. One must be careful.
IP Logged
jhm
Frequent Elocutionist
Offline
Posts: 1403
Location: georgia
Joined: Sep 4
th
, 2011
Re: model 33 Husqvarna
Reply #12 -
Sep 2
nd
, 2018 at 8:27pm
Print Post
Bet I know where you got it! Have you been attending the Montrose auctions lately? Recently they have had lots of rollers. I picked up a nice model 53 win couple weeks ago and they also had another Husky.
JMH
IP Logged
Fazer
Full Member
Offline
Posts: 248
Joined: Jun 9
th
, 2010
Re: model 33 Husqvarna
Reply #13 -
Sep 2
nd
, 2018 at 9:19pm
Print Post
Quote:
Have you been attending the Montrose auctions lately
I've had that one for tens years at least.
IP Logged
rollingblock
Senior Forum Member
Offline
Posts: 383
Location: Texas part of New Mexico
Joined: Aug 19
th
, 2012
Re: model 33 Husqvarna
Reply #14 -
Sep 2
nd
, 2018 at 9:53pm
Print Post
I wish one would follow me home, must be nice. I always end up having to buy mine. Darn.
IP Logged
Pages:
[1]
2
Send Topic
Print
‹
Previous Topic
|
Next Topic
›
Forum Jump »
Board Index
» 10 most recent Posts
» 10 most recent Topics
General
Announcements
General Discussion
Single Shot Rifles
Reloading the Single Shot Rifle
Gunsmithing Single Shot Rifles
Collecting Single Shot Rifles
Hunting with Single Shot Rifles
Rifle Photos ««
ASSRA Match Scores
For Sale/Trade
Support and Feedback
ASSRA.COM Feedback and Suggestions
Forum Help
Membership Support
« Board Index
‹ Board
ASSRA Forum
» Powered by
YaBB 2.6.12
!
YaBB Forum Software
© 2000-2024. All Rights Reserved.
Page completed in 0.9187 seconds.