ASSRA Forum › General › Gunsmithing Single Shot Rifles › Question on bore diameter.
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Question on bore diameter. (Read 2313 times)
Elalto
Junior Member
**
Offline



Posts: 76
Location: Chula Vista, CA
Joined: Oct 5th, 2004
Question on bore diameter.
Nov 17th, 2017 at 1:06pm
Print Post  
Hi All,

I have a Winchester Low Wall with a Stevens Model 416 "Circle X" .22 RF barrel that has been re chambered to.22 Hornet. I am about to load up some ammo for it and was wondering if I should use .223" bullets or will the .224" bullets work?

Thanks in advance,
Marcos (elalto)
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 16159
Location: Oregon
Joined: Feb 2nd, 2009
Re: Question on bore diameter.
Reply #1 - Nov 17th, 2017 at 4:19pm
Print Post  
I would slug the bore and determine what bullet you should use.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
Schuetzendave
Frequent Elocutionist
*****
Offline


Retired Ex-Shooter

Posts: 4052
Location: St. Albert, Alberta
Joined: Jan 28th, 2005
Re: Question on bore diameter.
Reply #2 - Nov 17th, 2017 at 6:41pm
Print Post  
If using jacketed bullets I would stay with .223 bullets for what was originally a .22RF barrel with a .223 groove-to-groove diameter.

When using cast bullets you can use the same diameter bullet as the groove-to-groove diameter or larger; by as much as .002", so you could use either a .223 or .224 diameter cast lead:tin bullets.
  
Back to top
 
IP Logged
 
Elalto
Junior Member
**
Offline



Posts: 76
Location: Chula Vista, CA
Joined: Oct 5th, 2004
Re: Question on bore diameter.
Reply #3 - Nov 17th, 2017 at 9:13pm
Print Post  
Thank you, Dave.

I was pretty sure that was the case but just wanted to have it confirmed.

Thanks again,
Marcos (elalto)
  
Back to top
 
IP Logged
 
waterman
Frequent Elocutionist
*****
Offline



Posts: 2838
Location: Behind the Redwood Curtain
Joined: Jun 9th, 2004
Re: Question on bore diameter.
Reply #4 - Nov 18th, 2017 at 3:25am
Print Post  
I had one just like that.  Groove diameter was just under .223".  Use the .223 bullets and light loads just so you do not burn out the barrel.
  
Back to top
 
IP Logged
 
John Taylor
Frequent Elocutionist
*****
Offline



Posts: 1695
Location: Lewiston, ID
Joined: Oct 23rd, 2006
Re: Question on bore diameter.
Reply #5 - Nov 19th, 2017 at 12:21pm
Print Post  
The older Winchesters use a .223 ( 22 LR ) barrel for the Hornet, even on the model 70 bolt action.
  
John Taylor   Machinist/gunsmith
Back to top
WWW  
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.5962 seconds.