ASSRA Forum - Breech seating using Stevens action?

ASSRA Forum › General › Reloading the Single Shot Rifle › Breech seating using Stevens action?

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1

Breech seating using Stevens action? (Read 2391 times)

StevenHall Junior Member Offline Posts: 92 Location: Cave Creek, AZ Joined: Sep 23^rd, 2014	Breech seating using Stevens action? Nov 18^th, 2016 at 2:05am	Print Post
	I was looking though CPA's website and it says you can use the Stevens action to breech seat bullets without using a mechanical seater. Have any of you tried this with much success? I assume this would work with the 44 action as well and not just the 44 1/2? I am thinking of contacting Rocky Mountain Cartridge to see if they would make a solid case with the same outside dimensions, but not hollowed out. Is it worth fiddling with?


	IP Logged

frnkeore Frequent Elocutionist Offline Posts: 7665 Location: Central Point, OR 97502 Joined: Jun 16^th, 2010	Re: Breech seating using Stevens action? Reply #1 - Nov 18^th, 2016 at 2:30am	Print Post
	It will work pretty well and the 44 action has more travel and leverage than a 44 1/2 to BS. You don't need to have a case made, you can just make a piece of brass to slide inside the fire formed case or even use a hardwood dowel. If you use brass, you can thread the end that goes into the case for a 1/4" set screw so that you can adjust your BS depth. On a 44 1/2, using a ~200 gr bullet, a tapered bullet will help you get the bullet far enough in to have enough travel with the breech block to get it BSed w/o trouble. There are different ways to set the BSer but, the easiest method is to have at least 2/3 of the base band engraved with rifling, and adjust from that point, usually deeper. You'll love how much better it shoots BSed Enjoy, Frank

	ASSRA Member #696, ISSA Member #339
	YIM AIM IP Logged

Schuetzenmiester Frequent Elocutionist Offline Posts: 6707 Location: Cool Wet Side of WA Joined: Apr 27^th, 2008	Re: Breech seating using Stevens action? Reply #2 - Nov 18^th, 2016 at 3:02am	Print Post
	I used to BS a 44 1/2 with a push rod type seater. I had a door knob type handle. I pushed the bullet in a popped it with the heal of my hand. Shot 248 with it back when 250s were unheard of

	"some old things are lovely, warm still with life ... of the forgotten men who made them." - D.H. Lawrence
	IP Logged

StevenHall Junior Member Offline Posts: 92 Location: Cave Creek, AZ Joined: Sep 23^rd, 2014	Re: Breech seating using Stevens action? Reply #3 - Nov 18^th, 2016 at 12:30pm	Print Post
	Thanks, can't wait to try it out.


	IP Logged

waterman Frequent Elocutionist Offline Posts: 3003 Location: Behind the Redwood Curtain Joined: Jun 9^th, 2004	Re: Breech seating using Stevens action? Reply #4 - Nov 19^th, 2016 at 1:31am	Print Post
	I breech-seat with my Stevens rifles with 44 actions using a fired case filled with a wooden dowel. I do this with both 28-30 and 25-20 SS cases. No specially-made cases. Just hardwood dowels and a bit of sandpaper to adjust seating depth. Not fancy, but it works very well if you stick to soft lead bullets.


	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

Page completed in 1.3300 seconds.