(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic What is it? (Read 3542 times)
Redsetter
Frequent Elocutionist
*****
Offline



Posts: 3468
Location: New York
Joined: Aug 6th, 2013
What is it?
May 19th, 2016 at 10:30am
Print Post  
Guess there can't be much doubt, though the dovetailed casting itself looks like a machine tool fixture.  I even know with 99.9% certainty--but unfortunately cannot prove--who built it: gunsmith & inventor John Wilkinson originally of Keesville, NY, later moving to Plattsburgh, NY.
  
Back to top
 
IP Logged
 
KAF
Ex Member


Re: What is it?
Reply #1 - May 19th, 2016 at 10:35am
Print Post  
Back part of a machine rest.
  
Back to top
 
IP Logged
 
40_Rod
Frequent Elocutionist
*****
Offline


Extremism in the persuit
of accuracy is not a
vice

Posts: 4285
Location: Knoxville, TN
Joined: Apr 20th, 2004
Re: What is it?
Reply #2 - May 20th, 2016 at 8:55am
Print Post  
It looks like the front  of a machine rest you can see where the plate was milled to accept a particular barrel.

40 Rod
  
Back to top
 
IP Logged
 
CajunRebel
Oldtimer
*****
Offline



Posts: 692
Location: Alexandria, VA
Joined: Nov 18th, 2007
Re: What is it?
Reply #3 - May 20th, 2016 at 11:54am
Print Post  
I'm in Vienna, can't text address from phone.  Look under Gunsmithing SS, Muzzle Rest/Sleds, Reply #72, 05/01/16.  There is a photo of a brass setup.  Think it'll answer your question.  I have seen a photo of your exact setup as a stock rest for a sled.  Stock bottom was perfectly flat with a metal flat.
  
Back to top
 
IP Logged
 
westerner
Frequent Elocutionist
*****
Offline


deleted posts and threads
record holder.

Posts: 11518
Location: Why, out West of course
Joined: May 29th, 2006
Re: What is it?
Reply #4 - May 24th, 2016 at 6:13pm
Print Post  
They don't make wingnuts like that anymore.


         Joe.
  
A blind squirrel runs into a tree every once in a while.
Back to top
 
IP Logged
 
QuestionableMaynard8130
Frequent Elocutionist
*****
Offline



Posts: 4144
Location: Benton  Harbor MI
Joined: Apr 17th, 2004
Re: What is it?
Reply #5 - May 24th, 2016 at 6:50pm
Print Post  
machine rest for testing barrels and loads.    the wooden forend-less barrels was rested on it's bottom flat   clamp-on muzzle rest/ sled/ bob-sled. was attached near the muzzle. it had a notch the was used with a locator pin mounted in the wooden plank the formed the third part of the machine rest. The rear part that you have pictured was attached to the rear edge of the end of the plank.  the action and butt stock hung out in the air behind the bench or stand the whole apparatus was clamped to.  the rest simply provided a secure solid "return to battery" firing position.

It might have also been used in the same manner in early Northeastern "slug-gun" competition.
  
sacred cows make the best burger
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.4778 seconds.