ASSRA Forum › General › Collecting Single Shot Rifles › Another date request - Stevens 44
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Another date request - Stevens 44 (Read 3996 times)
Travelor
Full Member
***
Offline



Posts: 132
Location: Central Arkansas
Joined: May 5th, 2008
Another date request - Stevens 44
May 2nd, 2016 at 7:58am
Print Post  
Sorry for the redundancy, but no references found.

I have a Stevens 44 serial number 163xx in 22 LR with a 24" #2 barrel half round half octagon and "hooked" steel butt plate all matching serial numbers.  It has a Lyman tang sight and shows good color case hardening under the sight.

Any idea when it was made?
« Last Edit: May 2nd, 2016 at 1:42pm by Travelor »  
Back to top
 
IP Logged
 
frnkeore
Frequent Elocutionist
*****
Offline



Posts: 7324
Location: Central Point, OR 97502
Joined: Jun 16th, 2010
Re: Anothe date request Stevens 44
Reply #1 - May 2nd, 2016 at 12:22pm
Print Post  
Does it have a 6 or 7 o'clock extractor?

Frank
  
ASSRA Member #696, ISSA Member #339
Back to top
YIMAIM  
IP Logged
 
Travelor
Full Member
***
Offline



Posts: 132
Location: Central Arkansas
Joined: May 5th, 2008
Re: Anothe date request Stevens 44
Reply #2 - May 2nd, 2016 at 1:40pm
Print Post  
It has a 7 o'clock extractor.
  
Back to top
 
IP Logged
 
Travelor
Full Member
***
Offline



Posts: 132
Location: Central Arkansas
Joined: May 5th, 2008
Re: Anothe date request Stevens 44
Reply #3 - May 2nd, 2016 at 1:42pm
Print Post  
It has a 7 o'clock extractor.
  
Back to top
 
IP Logged
 
frnkeore
Frequent Elocutionist
*****
Offline



Posts: 7324
Location: Central Point, OR 97502
Joined: Jun 16th, 2010
Re: Another date request - Stevens 44
Reply #4 - May 2nd, 2016 at 2:00pm
Print Post  
I don't know the exact date but, the 7 o'clock extractor, ended sometime after 1900.

Some others will be able to give a better date.

Frank
  
ASSRA Member #696, ISSA Member #339
Back to top
YIMAIM  
IP Logged
 
uscra112
Frequent Elocutionist
*****
Offline



Posts: 4079
Location: Switzerland of Ohio
Joined: May 7th, 2007
Re: Another date request - Stevens 44
Reply #5 - May 2nd, 2016 at 3:00pm
Print Post  
Look to see if you have screw heads on the right side.

Serial number puts in a relatively narrow range that had the side extractor, but also had the two-piece "bolt" pivots for lever and breechblock.  So it has to come just before the introduction of the 6 o'clock extractor.   

If so, I'd put it somewhere between 1900 and 1903.  The latter is the first dated catalog I have that refers to the central extractor and the "bolts", and 1900 is the last that I have which doesn't.   

Wish I had a full-line 1901 or 1902 catalog.  Abby at Cornell has an "abridged" 1902, which I suppose I should buy......
  
<div class=
Back to top
 
IP Logged
 
Travelor
Full Member
***
Offline



Posts: 132
Location: Central Arkansas
Joined: May 5th, 2008
Re: Another date request - Stevens 44
Reply #6 - May 4th, 2016 at 8:24am
Print Post  
uscra112, thank you for the information. 

The action is on its way to CPA for "refreshing" and color case hardening.  As far as screw heads, the action has been taken apart in the past so I have now way of knowing what the original direction the screws were in.  But they are two piece screws, on screwing into the center of the other.

  
Back to top
 
IP Logged
 
frnkeore
Frequent Elocutionist
*****
Offline



Posts: 7324
Location: Central Point, OR 97502
Joined: Jun 16th, 2010
Re: Another date request - Stevens 44
Reply #7 - May 4th, 2016 at 10:36am
Print Post  
If you look on the "bolts", you'll find a little projection, just under the rim, that goes into a notch in the action. It aliens the bolt and keeps it from turning, when you tighten the opposing screw.

Frank
  
ASSRA Member #696, ISSA Member #339
Back to top
YIMAIM  
IP Logged
 
slumlord44
Frequent Elocutionist
*****
Offline



Posts: 2850
Location: Lebanon, Illinois 62254
Joined: Dec 21st, 2007
Re: Another date request - Stevens 44
Reply #8 - May 4th, 2016 at 10:11pm
Print Post  
Without pulling one out to check, I think the "nut" part goes on the right and the "bolt" goes on the left. Someone correct me if I am wrong. As stated you should see the notch on the frame. A lot of these get damaged by people who don't know how it works.
  
Back to top
 
IP Logged
 
JCHannum
Senior Forum Member
****
Offline



Posts: 435
Location: Toledo
Joined: Aug 8th, 2007
Re: Another date request - Stevens 44
Reply #9 - May 5th, 2016 at 9:44am
Print Post  
The short screw goes in the right hand side of the action, the shouldered pin the left hand side. Right and left being with the rifle at the shooter's shoulder.
  
Jim H.
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.9347 seconds.