ASSRA Forum › General › Gunsmithing Single Shot Rifles › Uberti parts
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Uberti parts (Read 3844 times)
tdelewis
Full Member
***
Offline



Posts: 119
Joined: Aug 22nd, 2013
Uberti parts
Jul 15th, 2015 at 8:03pm
Print Post  
I'm sure the answer is no but just need to ask.  Will the parts from Uberti low wall and high wall  interchange with original Winchesters?  I would imagine that all the threads are metric on Italian guns.
  
Back to top
 
IP Logged
 
John Boy
Ex Member


Re: Uberti parts
Reply #1 - Jul 15th, 2015 at 10:27pm
Print Post  
Don't know the answer but if you call Taylor Firearms or Cimarron Firearms - ask for tech support - they'll give you the answer
  
Back to top
 
IP Logged
 
Grizz61
Participating Member
*
Offline



Posts: 10
Location: Aurora, CO
Joined: May 20th, 2015
Re: Uberti parts
Reply #2 - Jul 16th, 2015 at 12:38am
Print Post  
If you do call them, please post their answer.

I for one would be very interested in the answer.
  
Back to top
 
IP Logged
 
RBKenn
Senior Forum Member
****
Offline



Posts: 279
Location: fallon
Joined: Apr 8th, 2011
Re: Uberti parts
Reply #3 - Jul 16th, 2015 at 7:31pm
Print Post  
Last time I checked VTI gun parts was the factory distributer for all Uberti parts. I asked the same question about the #2 rolling block. They were kind enough to loan me all the parts. Unfortunately the answer is a resounding no.
  
Back to top
 
IP Logged
 
jlmurphy
Participating Member
*
Offline



Posts: 32
Location: Fallbrook, Ca.
Joined: Oct 22nd, 2010
Re: Uberti parts
Reply #4 - Jul 18th, 2015 at 11:32pm
Print Post  
My Uberti Hi Wall has standard 20 tpi barrel threads, and a fly cut high speed original hammer dropped in. The people at Taylor were kind enough to sell me an assembled DST lower tang for the cost of the parts. I have nothing but praise for the Uberti action and their support staff.
  
Back to top
 
IP Logged
 
Stractor
Junior Member
**
Offline



Posts: 94
Location: New Jersey
Joined: Jan 3rd, 2010
Re: Uberti parts
Reply #5 - Jul 23rd, 2015 at 1:49am
Print Post  
To answer the original question, not really. They are just slightly off . Some parts might be made to work like the hammer but it will need to be modified, they will not be drop in.I believe the parts are made to metric measurements (excluding the barrel threads) I compared a Uberti Schuetzen low wall parts to  Win low wall parts and it was a no go. I managed to squeeze an undersized Win Pope lever in a Uberti Schuetzen but the lever had to be bushed and a new pin made and shims added between the lever and the receiver but it works fine
« Last Edit: Jul 23rd, 2015 at 12:47pm by Stractor »  
Back to top
 
IP Logged
 
George Babits
Frequent Elocutionist
*****
Offline



Posts: 1109
Joined: Sep 27th, 2012
Re: Uberti parts
Reply #6 - Jul 23rd, 2015 at 9:56am
Print Post  
Why put foreign parts onto an American rifle?  MVA is making parts for the original h/low wall Winchester.  There are also several other shops making various parts for the Winchester single shots.

George
  
Back to top
 
IP Logged
 
Frankford
Full Member
***
Offline



Posts: 162
Location: Clint, TX
Joined: Dec 20th, 2012
Re: Uberti parts
Reply #7 - Jul 23rd, 2015 at 4:05pm
Print Post  
George, the answer is low price, availability and good quality.
Unfortunately, most metric parts will need modified to function in original actions. 
Metric Sharps 74 parts are also in a slightly different Spec.& Dim. that will resist use in originals, even as a temporary substitute. 

  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.4363 seconds.