ASSRA Forum › General › Reloading the Single Shot Rifle › Ballard .38 Long load data?
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Ballard .38 Long load data? (Read 3390 times)
StevenHall
Junior Member
**
Offline



Posts: 92
Location: Cave Creek, AZ
Joined: Sep 23rd, 2014
Ballard .38 Long load data?
Apr 7th, 2015 at 2:20pm
Print Post  
My Uncle just bought a nice Ballard in .38 Long and he is having a hard time finding loading data for it. Any load info will be helpful, but he is most interested in type/size of bullet and where he can get a mold.

Thanks.
  
Back to top
 
IP Logged
 
rgchristensen
Frequent Elocutionist
*****
Offline



Posts: 1185
Joined: Jan 2nd, 2014
Re: Ballard .38 Long load data?
Reply #1 - Apr 7th, 2015 at 3:36pm
Print Post  
STEVEN:
     Barber's book lists 140-150 gr bullet for the 38L RF, and presumably the CF would be the same.   It will take a heeled bullet, which will be the big problem.  A chamber cast will tell you a lot.   I prefer to use sulfur rather than Cerrosafe, easy to do, cheap, and gives 'good enough" results.   

CHRIS
RGChristensen
  
Back to top
 
IP Logged
 
bisaacson
Full Member
***
Offline



Posts: 170
Location: Kailua
Joined: Sep 1st, 2009
Re: Ballard .38 Long load data?
Reply #2 - Apr 7th, 2015 at 5:20pm
Print Post  
Bernie, Old West Moulds, 1175 17 1/4 Road, Fruita CO 81521 has a nice .38 heeled mould. Email: Allisonmonument@aol.com
  
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 17966
Location: Oregon
Joined: Feb 2nd, 2009
Re: Ballard .38 Long load data?
Reply #3 - Apr 7th, 2015 at 6:18pm
Print Post  
NEI also has a nice heeled bullet mold for the .38 Long. I use both an original Ideal mold, and a NEI mold for mine. I use a little plinker load of 3.0 grs. of Unique, which is around 650 fps. I run it up a little bit, but this is a good place to start, and maybe work up to 3.5 grs. of Unique.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
StevenHall
Junior Member
**
Offline



Posts: 92
Location: Cave Creek, AZ
Joined: Sep 23rd, 2014
Re: Ballard .38 Long load data?
Reply #4 - Apr 8th, 2015 at 11:15am
Print Post  
Thanks guys!
  
Back to top
 
IP Logged
 
Fred Boulton
Oldtimer
*****
Offline



Posts: 801
Joined: Jan 6th, 2007
Re: Ballard .38 Long load data?
Reply #5 - Apr 8th, 2015 at 2:38pm
Print Post  
It depends on your actual bore diameter (not groove ).
If a 38 special hollow based wadcutter doesn't just drop through the barrel but grips slightly on the bore, then this will probably shoot better than the correct heeled bullet. 
Fred
  
Back to top
 
IP Logged
 
bisaacson
Full Member
***
Offline



Posts: 170
Location: Kailua
Joined: Sep 1st, 2009
Re: Ballard .38 Long load data?
Reply #6 - Apr 8th, 2015 at 9:01pm
Print Post  
The heeled bullets I've used have shot surprisingly well given a lead alloy with about 2% tin to fill out the mould, and the right low pressure loads, as long as they fit the bore.
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.5740 seconds.