ASSRA Forum - Which moulds for .22 ?

ASSRA Forum › General › Reloading the Single Shot Rifle › Which moulds for .22 ?

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Hot Topic (More than 10 Replies)

Which moulds for .22 ? (Read 7073 times)

Cat_Whisperer Frequent Elocutionist Offline No 1, 9.3x74R Posts: 3982 Location: Mountains of Virginia Joined: Apr 17^th, 2004	Which moulds for .22 ? Jan 2^nd, 2015 at 9:19am	Print Post
	I'm just starting to get serious with the .22's. (Hornet, 221 and 223). Which moulds for plain-base? (I have several for GC, but need insight for the PB variety.) [GC in 22 are a pita!]

	Cat Whisperer (trk) Chief of Smoke Pulaski Coehorn Works and Skunk Works Drafted May 1970, Retired Maj. U.S.Army assra #9885
	WWW IP Logged

rkaires Frequent Elocutionist Offline No Stronger Bond Posts: 1671 Location: Dingmans Ferry, PA Joined: Oct 26^th, 2012	Re: Which moulds for .22 ? Reply #1 - Jan 2^nd, 2015 at 10:42am	Print Post
	This is a mould that B. Darr makes. Its a 70gr tapered spitzer. .225 on the base band.

	ASSRA #11031 NRA Life Proud Noodlehead "Peace is that brief, glorious moment in history, when everybody stands around reloading."~ ~ Thomas Jefferson
	IP Logged

rkaires Frequent Elocutionist Offline No Stronger Bond Posts: 1671 Location: Dingmans Ferry, PA Joined: Oct 26^th, 2012	Re: Which moulds for .22 ? Reply #2 - Jan 2^nd, 2015 at 10:48am	Print Post
	Here's a 68gr Pope style bullet NOE is making. They make it in both GC and PB. I spoke to them recently and was told they will be doing a run of plan base moulds this spring. I may pick one up myself to try in my .22WCF.

	ASSRA #11031 NRA Life Proud Noodlehead "Peace is that brief, glorious moment in history, when everybody stands around reloading."~ ~ Thomas Jefferson
	IP Logged

.22-5-40 Oldtimer Offline Posts: 826 Joined: Feb 13^th, 2010	Re: Which moulds for .22 ? Reply #3 - Jan 2^nd, 2015 at 1:00pm	Print Post
	You didn't specify twist, but my Hornet is 1-14" I had Fred leeth make up nose-pour copy of the old Ideal 22636 in both G.C. & plain-base @ 52grs. These are not tapered and are for fixed ammo. If shooting fixed, I found the most improvement in accuracy was to taper 1st. band in a die I made to fit std. lube-sizer to match leade angle. This band is fully engraved as action closes. Best of luck, the .22's are fun!


	IP Logged

Cat_Whisperer Frequent Elocutionist Offline No 1, 9.3x74R Posts: 3982 Location: Mountains of Virginia Joined: Apr 17^th, 2004	Re: Which moulds for .22 ? Reply #4 - Jan 2^nd, 2015 at 4:54pm	Print Post
	Looks like some good choices. (correct I did not specify the twist - 4 rifles to start with, expect that I have more than one twist rate, will check soon) The 22636 (from castpicks: (You need to *Login* or *Register* to view media files and links)) looks similar to the Pope style pictured previously). I like the concept of the Lovern style. Took the CZ527, TC Contender (21" bbl), Carl Walther (with double set trigger) and an H&R handi rifle to the range this afternoon. The Walther did the best (with the lightest loads too) and the CZ was second (with the hottest loads). I was playing with two vintages of the 225415 - the smallest (oldest) did the best. This was trip #1 to the range, LOTS more before any conclusions are drawn.

	Cat Whisperer (trk) Chief of Smoke Pulaski Coehorn Works and Skunk Works Drafted May 1970, Retired Maj. U.S.Army assra #9885
	WWW IP Logged

Larry D Full Member Offline Posts: 164 Location: Ventura ca. Joined: Jan 12^th, 2013	Re: Which moulds for .22 ? Reply #5 - Jan 2^nd, 2015 at 5:41pm	Print Post
	What is the max speed for tc leas bullets? Larry


	IP Logged

Larry D Full Member Offline Posts: 164 Location: Ventura ca. Joined: Jan 12^th, 2013	Re: Which moulds for .22 ? Reply #6 - Jan 2^nd, 2015 at 5:42pm	Print Post
	Tc bullets. Larry


	IP Logged

Cat_Whisperer Frequent Elocutionist Offline No 1, 9.3x74R Posts: 3982 Location: Mountains of Virginia Joined: Apr 17^th, 2004	Re: Which moulds for .22 ? Reply #7 - Jan 2^nd, 2015 at 7:39pm	Print Post
	Larry D wrote on Jan 2^nd, 2015 at 5:41pm: What is the max speed for tc lead bullets? Larry the CZ & TC are in .223, with the 225415 over 6.5, 7.0 and, 7.5 gr of Green Dot. from the book, 24" bbl, 6.2 = 1885fps and 9.2 = 2270fps. The Walther and the H&R in 22 Hornet, with the 225415 over 3.0, 3.5, and 4.0gr of Green Dot. Where, from the Lyman Cast Bullet Handbook, 2.5 gives 1350fps and 4.2 gives 1765. I shot not quite a hundred rounds, good start on getting to loading cast in .22's. I repeat, GC's in .22 are a PITA!

	Cat Whisperer (trk) Chief of Smoke Pulaski Coehorn Works and Skunk Works Drafted May 1970, Retired Maj. U.S.Army assra #9885
	WWW IP Logged

Cat_Whisperer Frequent Elocutionist Offline No 1, 9.3x74R Posts: 3982 Location: Mountains of Virginia Joined: Apr 17^th, 2004	Re: Which moulds for .22 ? Reply #8 - Jan 4^th, 2015 at 9:04am	Print Post
	.22-5-40 wrote on Jan 2^nd, 2015 at 1:00pm: You didn't specify twist, but my Hornet is 1-14" I had Fred leeth make up nose-pour copy of the old Ideal 22636 in both G.C. & plain-base @ 52grs. These are not tapered and are for fixed ammo. If shooting fixed, I found the most improvement in accuracy was to taper 1st. band in a die I made to fit std. lube-sizer to match leade angle. This band is fully engraved as action closes. Best of luck, the .22's are fun! How did you make the die? Pictures? (I have a lathe and a mill.)

	Cat Whisperer (trk) Chief of Smoke Pulaski Coehorn Works and Skunk Works Drafted May 1970, Retired Maj. U.S.Army assra #9885
	WWW IP Logged

QuestionableMaynard8130 Frequent Elocutionist Offline Posts: 4144 Location: Benton Harbor MI Joined: Apr 17^th, 2004	Re: Which moulds for .22 ? Reply #9 - Jan 4^th, 2015 at 8:25pm	Print Post
	NOE makes a bunch of them. Swede does a big business in group buy designs with the "CastBoolit" bunch. here's a link to their on-line store where he sells over production and production runs of popular designs. (You need to *Login* or *Register* to view media files and links)

	sacred cows make the best burger
	IP Logged

Cat_Whisperer Frequent Elocutionist Offline No 1, 9.3x74R Posts: 3982 Location: Mountains of Virginia Joined: Apr 17^th, 2004	Re: Which moulds for .22 ? Reply #10 - Jan 4^th, 2015 at 10:11pm	Print Post
	QuestionableMaynard8130 wrote on Jan 4^th, 2015 at 8:25pm: NOE makes a bunch of them. Swede does a big business in group buy designs with the "CastBoolit" bunch. here's a link to their on-line store where he sells over production and production runs of popular designs. (You need to *Login* or *Register* to view media files and links) I've seen the page - impressive collection! need more experience here to be able to flip the coin!

	Cat Whisperer (trk) Chief of Smoke Pulaski Coehorn Works and Skunk Works Drafted May 1970, Retired Maj. U.S.Army assra #9885
	WWW IP Logged

JS47 Frequent Elocutionist Offline Posts: 1265 Location: Arizona Joined: Oct 12^th, 2012	Re: Which moulds for .22 ? Reply #11 - Jan 4^th, 2015 at 10:52pm	Print Post
	How did you make the die? Pictures? (I have a lathe and a mill.) [/quote] It's easy enough to make a sizing die body and taper it with a throating reamer, if you have a throating reamer that is. JS


	IP Logged

.22-5-40 Oldtimer Offline Posts: 826 Joined: Feb 13^th, 2010	Re: Which moulds for .22 ? Reply #12 - Jan 5^th, 2015 at 6:48pm	Print Post
	At the time, I was working in a fully equipped tool room. Turned up die and after H.T., I.D. ground angle.


	IP Logged

Cat_Whisperer Frequent Elocutionist Offline No 1, 9.3x74R Posts: 3982 Location: Mountains of Virginia Joined: Apr 17^th, 2004	Re: Which moulds for .22 ? Reply #13 - Jan 6^th, 2015 at 9:23am	Print Post
	.22-5-40 wrote on Jan 5^th, 2015 at 6:48pm: At the time, I was working in a fully equipped tool room. Turned up die and after H.T., I.D. ground angle. Understand; thanks. I think my design will be for use with an arbor press (Schmidt) and made simply on the lathe.

	Cat Whisperer (trk) Chief of Smoke Pulaski Coehorn Works and Skunk Works Drafted May 1970, Retired Maj. U.S.Army assra #9885
	WWW IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.6682 seconds.