ASSRA Forum › General › Reloading the Single Shot Rifle › 32-40 Black powder
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic 32-40 Black powder (Read 2910 times)
Fazer
Full Member
***
Offline



Posts: 248
Joined: Jun 9th, 2010
32-40 Black powder
Jan 5th, 2014 at 3:44am
Print Post  
I want to start shooting the 32-40's with black powder. I will be  shooting paper up to 200 yards. Any suggestions on bullets.

I shoot larger calibres in black powder, but have never tried with the smaller ones. 

Are wads, cookies or something along those lines needed. Just hoping to get a starting point and go from there. 

Thanks
  
Back to top
 
IP Logged
 
westerner
Frequent Elocutionist
*****
Offline


deleted posts and threads
record holder.

Posts: 11463
Location: Why, out West of course
Joined: May 29th, 2006
Re: 32-40 Black powder
Reply #1 - Jan 5th, 2014 at 4:01am
Print Post  
Fixed, I load 40gr FFF, set a card wad or a Walters wad on the powder. Don't size my brass, just drop the bullet on the powder. I use tapered bullets as long as the twist allows. Have had best accuracy with bullets that fit the unsized case necks very close.

If you want to breech seat bullets, compressing the powder will eliminate separated cases. I made a tool to compress BP to the end of the case mouth. An air gap from the base of the bullet to the powder is okay. Maybe 30gr compressed powder works better than 40?  

Some wipe between shots and some use a blow tube.  I blow = Joeblow, ha ha, so funny.

  Good luck.

        Joe.
  
A blind squirrel runs into a tree every once in a while.
Back to top
 
IP Logged
 
gunlaker
Frequent Elocutionist
*****
Offline



Posts: 2272
Location: lower mainland, B.C.
Joined: Dec 13th, 2010
Re: 32-40 Black powder
Reply #2 - Jan 5th, 2014 at 7:19pm
Print Post  
Joe, how much compression do you use in order to prevent stretching and eventual separation?  I've got a really nice load going for my CPA in .38-55 but it does eventually stretch the brass a bit and I have lost a few cases.   

I'm using about 0.080" compression if I remember correctly.  I have read Steve Garbe's article on breech seating and case stretching.  I haven't tried a wad to take up space between the over powder wad and bullet yet but I likely will.  If I can't make that work I'll try annealing and then maybe RMC everlasting cases if it comes to that.

Chris.
  
Back to top
 
IP Logged
 
gunlaker
Frequent Elocutionist
*****
Offline



Posts: 2272
Location: lower mainland, B.C.
Joined: Dec 13th, 2010
Re: 32-40 Black powder
Reply #3 - Jan 5th, 2014 at 7:21pm
Print Post  
To the original poster,  with my .32-40 barrel on the CPA I've had pretty good results with the Saeco 200gr tapered bullet in 20:1 and a .030" veg wad.  Hopefully others with more experience than I do will have other suggestions.

Chris.
  
Back to top
 
IP Logged
 
westerner
Frequent Elocutionist
*****
Offline


deleted posts and threads
record holder.

Posts: 11463
Location: Why, out West of course
Joined: May 29th, 2006
Re: 32-40 Black powder
Reply #4 - Jan 6th, 2014 at 1:23am
Print Post  
Not sure how much compression, GL.  Was about five years ago. The tool is a die and plunger that is used at the bench when using one case. Thinking maybe 3/16 to a 1/4 inch compression.  Powder charge is compressed with just enough room left to seat a Walters wad or cork wad and be flush with the case mouth. Have had better luck with fixed ammo for offhand shooting. 

      Joe.
  
A blind squirrel runs into a tree every once in a while.
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.4503 seconds.