ASSRA Forum › General › Collecting Single Shot Rifles › Sharps idetification
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Sharps idetification (Read 4666 times)
mwhite49
Frequent Elocutionist
*****
Offline



Posts: 1600
Location: Camarillo California
Joined: Nov 14th, 2007
Sharps idetification
Mar 13th, 2013 at 9:34pm
Print Post  
I have picked up a Sharps and I think it is a conversion model but not sure even after looking in Sellers book. Any help here appreciated.
mike
  
Back to top
 
IP Logged
 
mwhite49
Frequent Elocutionist
*****
Offline



Posts: 1600
Location: Camarillo California
Joined: Nov 14th, 2007
Re: Sharps idetification
Reply #1 - Mar 13th, 2013 at 9:36pm
Print Post  
Here is a picture that shows a small hump under the back of the hammer.
  
Back to top
 
IP Logged
 
mwhite49
Frequent Elocutionist
*****
Offline



Posts: 1600
Location: Camarillo California
Joined: Nov 14th, 2007
Re: Sharps idetification
Reply #2 - Mar 13th, 2013 at 9:37pm
Print Post  
last one. this is in .45 cal with a new barrel.
  
Back to top
 
IP Logged
 
rglenz
Participating Member
*
Offline



Posts: 27
Joined: Nov 2nd, 2012
Re: Sharps idetification
Reply #3 - Mar 13th, 2013 at 11:06pm
Print Post  
Yes it is a conversion,last photo shows where the primer mechanism has been ground off.
  
Back to top
 
IP Logged
 
rglenz
Participating Member
*
Offline



Posts: 27
Joined: Nov 2nd, 2012
Re: Sharps idetification
Reply #4 - Mar 13th, 2013 at 11:33pm
Print Post  
I should have added,(the dog needed out)that the serial range for the 74 models roughly falls in the 150,000 to 160,000 range.They started with the "C" at 100,000.
  
Back to top
 
IP Logged
 
George Babits
Frequent Elocutionist
*****
Offline



Posts: 1106
Joined: Sep 27th, 2012
Re: Sharps idetification
Reply #5 - Mar 14th, 2013 at 9:58am
Print Post  
Looking at the triggers, I'd say it is a "Mecham" conversion.  You can tell more by looking at the "Old Reliable" stamping on the barrel and the shape of the forend.  It is detailed in the Sellers book.   

George
  
Back to top
 
IP Logged
 
70grains
Ex Member


Re: Sharps idetification
Reply #6 - Mar 14th, 2013 at 11:10am
Print Post  
you have a conversion, thick lockplate, panel on receiver has a slice in to accomadate the percussion hammer, screw in bottom of lockplate for priming system, meechem conversion usually has english rifling, non matching serial numbers, thicker forarm where it meets the receiver. lockplate will not have the scallops that you will see on the 69s and 74s unless its a factory conversion. good luck with your new toy.
  
Back to top
 
IP Logged
 
mwhite49
Frequent Elocutionist
*****
Offline



Posts: 1600
Location: Camarillo California
Joined: Nov 14th, 2007
Re: Sharps idetification
Reply #7 - Mar 15th, 2013 at 10:11am
Print Post  
I have Frank Sellers book and to me it looks like a Sharps conversion for Boker. Will not be able to tell 100% until I get it next week.
Mike
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 1.0561 seconds.