Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic 50-70 to 45 neck forming help (Read 594 times)
MerwinBray
Oldtimer
*****
Offline


Aw Gees

Posts: 951
Location: Kansas City, KS
Joined: Apr 17th, 2004
50-70 to 45 neck forming help
Oct 18th, 2026 at 12:02pm
Print Post  
I need to form some 50-70 brass to accept a .455ish projectile. My 45-70 dies don’t have a large enough opening to start a 50 case. Does anyone have experience or recommendations on how I should go about this? 
I’m basically making a 45 Peabody case. Or hoping to, at least.
  

Great Plains Precision Rifle Club
Back to top
 
IP Logged
 
oneatatime
Frequent Elocutionist
*****
Offline



Posts: 4600
Location: Rocky Mountains
Joined: Oct 30th, 2011
Re: 50-70 to 45 neck forming help
Reply #1 - Oct 19th, 2026 at 1:42am
Print Post  
I make my 500-450 #2 from 50-90 brass with very little effort just easing it in stages into the sizing die using Imperial Wax.
  
Back to top
 
IP Logged
 
Jaybird4
Participating Member
*
Offline



Posts: 16
Joined: Sep 13th, 2026
Re: 50-70 to 45 neck forming help
Reply #2 - Oct 19th, 2026 at 7:47am
Print Post  
Maybe a 577/450 Martini die with some of it cut off
  
Back to top
 
IP Logged
 
bullshop
Senior Forum Member
****
Offline



Posts: 465
Joined: Sep 14th, 2017
Re: 50-70 to 45 neck forming help
Reply #3 - Oct 19th, 2026 at 9:18am
Print Post  
I use Mag-Tech 32 gauge hulls to make both 50-70 and 43 Egyptian.  I load .451" bullets in the 43 Egyptian.
After first annealing I trim the brass to length for the 43 using a 50-70 file trim die adjusted to correct length. That also starts the first neck step down from 32 gauge. Then an RCBS FL die for 43  Egyptian is used in steps to the FL sizing of the case.  What I end up with must be similar to what you need because as stated I am loading 45 caliber bullets in the 43 Egyptian. 43 Bowmont dies should also work since 43 Egyptian cartridges can be fired in 43 Bowmont rifles .
  
Back to top
 
IP Logged
 
MerwinBray
Oldtimer
*****
Offline


Aw Gees

Posts: 951
Location: Kansas City, KS
Joined: Apr 17th, 2004
Re: 50-70 to 45 neck forming help
Reply #4 - Oct 19th, 2026 at 10:52pm
Print Post  
This is great information and appreciated. I know I have a little more research and measuring to do. And now, probably should get a set of close bottleneck dies. 

I could use 43 Spanish dies for a couple of rolling blocks. I wonder if I would over work the brass by squeezing it down to 43, then back out to 45?
  

Great Plains Precision Rifle Club
Back to top
 
IP Logged
 
MerwinBray
Oldtimer
*****
Offline


Aw Gees

Posts: 951
Location: Kansas City, KS
Joined: Apr 17th, 2004
Re: 50-70 to 45 neck forming help
Reply #5 - Oct 19th, 2026 at 10:54pm
Print Post  
I could also use the 577-450, but, darn, they are pricey and I don’t have a press with the larger hole.
  

Great Plains Precision Rifle Club
Back to top
 
IP Logged
 
bullshop
Senior Forum Member
****
Offline



Posts: 465
Joined: Sep 14th, 2017
Re: 50-70 to 45 neck forming help
Reply #6 - Oct 20th, 2026 at 1:21pm
Print Post  
I dont know if they still do but for sure the older RCBS Rock Chucker is bored and threaded for 1 1/4 x 20 then bushed to 7/8x14.  Remove the bushing and you can use the large diameter 1 1/4x 20 Lee dies.
  
Back to top
 
IP Logged
 
George Babits
Frequent Elocutionist
*****
Offline



Posts: 1162
Joined: Sep 27th, 2012
Re: 50-70 to 45 neck forming help
Reply #7 - Oct 23rd, 2026 at 4:35pm
Print Post  
I'm not sure whether you are making 45-50 CF or a 45 rimfire, but here's how I've been making 45-45 Peabody RF brass from 50-70.  First I trim to approximate length.  Then I use my Lyman 45-70 expander die with the expander plug removed to start with.   That doesn't take the neck all the way down, so I follow up with the 45-70 seating die.  I keep the carbine handy, test my sizing down as I go,  and quit when the case chambers easily.  After doing that I plug the trimer hole and drill the base for a 22 RF blank.   I need to make more this winter.

George
  
Back to top
 
IP Logged
 
John in PA
Oldtimer
*****
Offline



Posts: 592
Location: Hollidaysburg, PA
Joined: Nov 3rd, 2009
Re: 50-70 to 45 neck forming help
Reply #8 - Today at 4:43pm
Print Post  
IS the end product supposed to be .45 Romanian Peabody, or the .45-50 Peabody Sporting? If it's the latter, you really need to start out with .43 Spanish or .44-77 to get the rim/head dimensions close. If it's the .45 Romanian, then here's my info (You need to Login or Register to view media files and links)

(You need to Login or Register to view media files and links)
  

John Wells
Hollidaysburg, PA
Peabody and Peabody-Martini's Wanted!
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint