ASSRA Forum - 357 MAX BRASS

ASSRA Forum › General › For Sale/Trade › 357 MAX BRASS

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Normal Topic

357 MAX BRASS (Read 297 times)

Oldman1950 Senior Forum Member Offline Posts: 268 Location: Virginia Joined: Feb 8^th, 2014	357 MAX BRASS May 28^th, 2026 at 4:23pm	Print Post
	I have for sale 50 pieces of 357 REM MAX brass with R.P head stamp. It looks to be new brass $25 plus $10 shipping. I accept personal checks A. J. Palik/size]


	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3756 Location: East Olympia, WA Joined: May 18^th, 2008	Re: 357 MAX BRASS Reply #1 - May 28^th, 2026 at 5:42pm	Print Post
	I will take the brass. PM sent Jack


	IP Logged

Oldman1950 Senior Forum Member Offline Posts: 268 Location: Virginia Joined: Feb 8^th, 2014	Re: 357 MAX BRASS Reply #2 - May 28^th, 2026 at 5:53pm	Print Post
	The Brass is SOLD to bpjack pending funds A. J. Palik


	IP Logged

RJ-35-40 Senior Forum Member Offline Posts: 314 Joined: Dec 7^th, 2016	Re: 357 MAX BRASS Reply #3 - May 28^th, 2026 at 10:41pm	Print Post
	Jack, That's a good deal. If your looking to buy more Starline has them in stock for about the same price. Bob in Saint Augustine... bpjack wrote on May 28^th, 2026 at 5:42pm: I will take the brass. PM sent Jack


	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3756 Location: East Olympia, WA Joined: May 18^th, 2008	Re: 357 MAX BRASS Reply #4 - May 28^th, 2026 at 11:46pm	Print Post
	I prefer the Remington brass. I will be reforming into 30-30 Wesson, 32 RKS and eventually leaving. them as is id I ever get my 35 cal barrel installed. I bought a 357 Max reamer a few months back. Jack


	IP Logged

RJ-35-40 Senior Forum Member Offline Posts: 314 Joined: Dec 7^th, 2016	Re: 357 MAX BRASS Reply #5 - yesterday at 10:05am	Print Post
	Jack, Is the Web near the base thicker on the Remington brass..? 'Unless you already know...... If you think of it AND it's easy please let us know how many grains of water the Remington brass holds. THX bpjack wrote on May 28^th, 2026 at 11:46pm: I prefer the Remington brass. I will be reforming into 30-30 Wesson, 32 RKS and eventually leaving. them as is id I ever get my 35 cal barrel installed. I bought a 357 Max reamer a few months back. Jack


	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3756 Location: East Olympia, WA Joined: May 18^th, 2008	Re: 357 MAX BRASS Reply #6 - yesterday at 1:58pm	Print Post
	I just prefer Rem brass after switching to it in my 25-20 Win. The Rem does not result in neck separation in that caliber when breech seating. I keep trying to measure the case volume with water, but so far by the time I make it from the kitchen sink to my shop, the water leaks out the little hole in the bottom. Jack


	IP Logged

bpjack Frequent Elocutionist Offline Posts: 3756 Location: East Olympia, WA Joined: May 18^th, 2008	Re: 357 MAX BRASS Reply #7 - yesterday at 2:12pm	Print Post
	I managed to run fast enough this time and got a reading of 34.1gr. measured with water rounded over on top. Shall I see if beer would weigh the same?


	IP Logged

RJ-35-40 Senior Forum Member Offline Posts: 314 Joined: Dec 7^th, 2016	Re: 357 MAX BRASS Reply #8 - yesterday at 3:20pm	Print Post
	Still Laughing... Beer..? Better use a 'duplex' load mixed with 150 proof grain alcohol. Burn rare is cleaner , faster. Rounded over the top you say... bpjack wrote yesterday at 2:12pm: I managed to run fast enough this time and got a reading of 34.1gr. measured with water rounded over on top. Shall I see if beer would weigh the same?


	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2026. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 1.4131 seconds.