ASSRA Forum - O. A. Bremer Rifle

ASSRA Forum › General › Single Shot Rifles › O. A. Bremer Rifle

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: [1]

Hot Topic (More than 10 Replies)

O. A. Bremer Rifle (Read 1038 times)

Oldman1950 Full Member Offline Posts: 249 Location: Virginia Joined: Feb 8^th, 2014	O. A. Bremer Rifle Oct 10^th, 2025 at 7:42pm	Print Post
	OOOP'S I did it again. The "no more rifles for me didn't work." This time it is a high wall by O. A. Bremer, San Francisco. I am sure I paid too much at auction for it but none the less it's now mine. Showed up via UPS this afternoon. First job was run a brush thru the bore to see what I have. Several strokes with a brush followed with a few patches. Out came my Tesalong borescope and I found the bore at 99%. Dropped the breach block and cleaned out the old lube. The hammer has been modified with the thumb piece removed and only a full cock notch remains. No fly. The triggers I am sure are Bremers. The set trigger sets but will not drop the hammer with the first pull but always work correctly with the second set and pull. I will do more work on them in the near future. The front trigger pull, with not being set, is real heavy but will drop the hammer. The bore is 22 short. A 22 lr. will not chamber. The barrel is a #3 Winchester, 28". The front sight is a Beach globe and the rear is a Lyman with the windage adjustable top. The adjustments on the sight are real stiff but a little oil and they now work fine. The barrel has been drilled for scope blocks set at 9" on center. The extractor is in great shape and the firing pin is also good with .040" tip with the hammer down. Now I have get to the range and see what it will do. Anyone else have and experance with Bremer triggers? A. J. Palik
	« Last Edit: Oct 10^th, 2025 at 9:15pm by Oldman1950 »

	IP Logged

Oldman1950 Full Member Offline Posts: 249 Location: Virginia Joined: Feb 8^th, 2014	Re: O. A. Bremer Rifle Reply #1 - Oct 10^th, 2025 at 7:48pm	Print Post
	A few more


	IP Logged

DWT1885 Senior Forum Member Offline Posts: 440 Location: New Jersey Joined: Nov 25^th, 2010	Re: O. A. Bremer Rifle Reply #2 - Oct 10^th, 2025 at 8:21pm	Print Post
	Nice looking target rifle you have there. I have also told myself "No more rifles". I'm just wondering what will I buy next. It's a sickness as you well know. Anyway, enjoy it A.J. Let us know how it shoots. Dale.

	35th Security Police Squadron, Phan Rang AB, RVN, May 70-71. All gave some, some gave all.
	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 17212 Location: Oregon Joined: Feb 2^nd, 2009	Re: O. A. Bremer Rifle Reply #3 - Oct 10^th, 2025 at 8:27pm	Print Post
	Bremer's custom scheutzen single shot rifles are some of the finest made! Not as well known as the big names, but his triggers are some of the best I've ever felt. His stocks are just perfect, without being so specialized as to only fit the original shooter. They just have a beautiful style that I really like. I'd be happy to own a Bemer if I found one I could afford, regardless. I think he's one of the great masters.

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

jimmy Senior Forum Member Offline Now available in Oklahoma. Posts: 353 Location: Skiatook Joined: May 12^th, 2009	Re: O. A. Bremer Rifle Reply #4 - Oct 10^th, 2025 at 8:28pm	Print Post
	Did you recently win the lottery? Beautiful rifle.


	IP Logged

Schutzenbob Frequent Elocutionist Offline Rheinisch-Westfälisc hen Sprengstoff-Fabriken Posts: 2185 Location: Nightingale, California Joined: Oct 24^th, 2005	Re: O. A. Bremer Rifle Reply #5 - Oct 10^th, 2025 at 8:29pm	Print Post
	Otto A. Bremer (You need to *Login* or *Register* to view media files and links)


	IP Logged

Schutzenbob Frequent Elocutionist Offline Rheinisch-Westfälisc hen Sprengstoff-Fabriken Posts: 2185 Location: Nightingale, California Joined: Oct 24^th, 2005	Re: O. A. Bremer Rifle Reply #6 - Oct 10^th, 2025 at 8:51pm	Print Post
	Bremer tool and Bullseye Bullets
	« Last Edit: Oct 10^th, 2025 at 9:25pm by Schutzenbob »

	IP Logged

westerner Frequent Elocutionist Online deleted posts and threads record holder. Posts: 11909 Location: Why, out West of course Joined: May 29^th, 2006	Re: O. A. Bremer Rifle Reply #7 - Oct 11^th, 2025 at 10:17am	Print Post
	Gorgeous!

	A blind squirrel runs into a tree every once in a while.
	IP Logged

Nate Junior Member Offline Posts: 57 Location: Northeast Joined: Oct 29^th, 2024	Re: O. A. Bremer Rifle Reply #8 - Oct 12^th, 2025 at 8:17am	Print Post
	Ha! I was bidding on that but you beat me!!! It’s a beautiful rifle and I am happy that you got it! Good luck with the triggers and keep us posted! They are great with packing and shipping-aren’t they!


	IP Logged

Oldman1950 Full Member Offline Posts: 249 Location: Virginia Joined: Feb 8^th, 2014	Re: O. A. Bremer Rifle Reply #9 - Oct 12^th, 2025 at 9:33pm	Print Post
	This afternoon I had some time so I disassembled the breach block. The hammer has been lightened and the spur has been ground off. There is no half cocked notch as it is being used as a full cock notch. When the lever is lowered the hammer goes to full cock and there isn't any way to lower the hammer other than pulling the trigger. I do not like to dry fire without a round in the chamber. I have another hammer coming to me so I will refit the rifle so I can lower the hammer with the hammer spur. Here is some pictures of the hammer in the rifle and the one I am going to replace it with. A. J. Palik


	IP Logged

Schutzenbob Frequent Elocutionist Offline Rheinisch-Westfälisc hen Sprengstoff-Fabriken Posts: 2185 Location: Nightingale, California Joined: Oct 24^th, 2005	Re: O. A. Bremer Rifle Reply #10 - Oct 12^th, 2025 at 9:41pm	Print Post
	I have a Bremer rifle with Bremer's patent triggers. At least on my rifle, I can push the back trigger forward while closing the action and lower the hammer.


	IP Logged

bpjack Frequent Elocutionist Online Posts: 3357 Location: East Olympia, WA Joined: May 18^th, 2008	Re: O. A. Bremer Rifle Reply #11 - Oct 12^th, 2025 at 11:00pm	Print Post
	You may run into an issue where the hammer drops into 1/2 cock with that standard replacement hammer. That is why the fly is installed on Winchester set trigger hammers. The simple solution unless you want to source a hammer with a fly is to grind off the 1/2 cock notch. Jack

	ASSRA # 11318 There are more hydrogen atoms in a single molecule of water than there are suns in the entire solar system.
	IP Logged

Oldman1950 Full Member Offline Posts: 249 Location: Virginia Joined: Feb 8^th, 2014	Re: O. A. Bremer Rifle Reply #12 - Oct 12^th, 2025 at 11:26pm	Print Post
	I will only use this rifle at the range and only load it when I am ready to shoot. The original hammer uses the half cock notch as a full cock notch. I thought I would use some JB weld and plug the half cock notch and see how the trigger pull is. If I am not happy with that then I will do some grinding on the hammer. If I grind the hammer and use the half cock notch I most likely need to reharden it. I have some Kasenit on hand. QUESTION: if I reharden the hammer should I draw the temper and if so what temperature should I use? A. J. Palik


	IP Logged

Oldman1950 Full Member Offline Posts: 249 Location: Virginia Joined: Feb 8^th, 2014	Re: O. A. Bremer Rifle Reply #13 - Oct 17^th, 2025 at 5:56pm	Print Post
	Today I was able to install the new to me hammer. I filled the half cock notch with JB Weld after super cleaning the notch so it would bond. When fully hardened it was dressed with a file. I might have to do something to the Bremer Patented triggers as they set OK but will not drop the hammer until the second set and pull. It does this every time and I am wondering if they were designed this way. Someone chimed in and said that they also had a Brener with patented triggers and I am wondering if theirs work the same. I hope to get to the range in the next couple of days to see how it shoots. I have 5 different kinds of 22 shorts on hand. The pictures are with the original hammer and with the new hammer. A. J. Palik


	IP Logged

westerner Frequent Elocutionist Online deleted posts and threads record holder. Posts: 11909 Location: Why, out West of course Joined: May 29^th, 2006	Re: O. A. Bremer Rifle Reply #14 - Oct 17^th, 2025 at 6:17pm	Print Post
	My sons Bremmer HW with Bremer triggers works normally. I don't see any advantage in the Bremer triggers. The hammer should fall when you trip the trigger every time. Something is amiss with a spring somewhere. Maybe to much spring pressure on the sear or not enough pressure on the rear trigger. Or something is binding and slowing trigger / sear action. Needs a fly?

	A blind squirrel runs into a tree every once in a while.
	IP Logged

bpjack Frequent Elocutionist Online Posts: 3357 Location: East Olympia, WA Joined: May 18^th, 2008	Re: O. A. Bremer Rifle Reply #15 - Oct 17^th, 2025 at 6:43pm	Print Post
	Try loosening the screw that holds the sear spring to make it a bit weaker to see if that is the issue.

	ASSRA # 11318 There are more hydrogen atoms in a single molecule of water than there are suns in the entire solar system.
	IP Logged

Oldman1950 Full Member Offline Posts: 249 Location: Virginia Joined: Feb 8^th, 2014	Re: O. A. Bremer Rifle Reply #16 - Oct 17^th, 2025 at 6:58pm	Print Post
	I will try loosening the sear spring and see if that is the problem. The set trigger spring seems to be about right but may have weakened over the years. Thanks for the ideas. I will keep you updated A. J. Palik


	IP Logged

Oldman1950 Full Member Offline Posts: 249 Location: Virginia Joined: Feb 8^th, 2014	Re: O. A. Bremer Rifle Reply #17 - Oct 18^th, 2025 at 12:49pm	Print Post
	PROBLEN SOLVED The sear spring was too firm. 20 minutes with a diamond stone and adjustment to the sear spring screw and the set trigger works every time. A BIG thank you to westerner and bpjack for sending me in the right direction. A. J. Palik


	IP Logged

Oldman1950 Full Member Offline Posts: 249 Location: Virginia Joined: Feb 8^th, 2014	Re: O. A. Bremer Rifle Reply #18 - Oct 18^th, 2025 at 8:12pm	Print Post
	?


	IP Logged

bpjack Frequent Elocutionist Online Posts: 3357 Location: East Olympia, WA Joined: May 18^th, 2008	Re: O. A. Bremer Rifle Reply #19 - Oct 18^th, 2025 at 8:22pm	Print Post
	Glad you got it fixed.

	ASSRA # 11318 There are more hydrogen atoms in a single molecule of water than there are suns in the entire solar system.
	IP Logged

westerner Frequent Elocutionist Online deleted posts and threads record holder. Posts: 11909 Location: Why, out West of course Joined: May 29^th, 2006	Re: O. A. Bremer Rifle Reply #20 - Oct 19^th, 2025 at 10:32am	Print Post
	That'll be a dollar two ninety five please.

	A blind squirrel runs into a tree every once in a while.
	IP Logged

westerner Frequent Elocutionist Online deleted posts and threads record holder. Posts: 11909 Location: Why, out West of course Joined: May 29^th, 2006	Re: O. A. Bremer Rifle Reply #21 - Oct 19^th, 2025 at 10:38am	Print Post
	Super neat rifle. Now a gallery match. League? Postal?

	A blind squirrel runs into a tree every once in a while.
	IP Logged

Page Index Toggle

Pages: [1]

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.6270 seconds.