ASSRA Forum - RCBS 41-260 FN mold

ASSRA Forum › General › For Sale/Trade › RCBS 41-260 FN mold

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Hot Topic (More than 10 Replies)

RCBS 41-260 FN mold (Read 486 times)

axman Participating Member Offline Posts: 24 Joined: Feb 1^st, 2010	RCBS 41-260 FN mold May 15^th, 2025 at 7:42pm	Print Post
	RCBS 41-260 FN 2 cavity mold. Discontinued by rcbs. In excellent condition. $120.00 Shipped in the USA Only.
	« Last Edit: Jun 1^st, 2025 at 9:10pm by axman »

	IP Logged

axman Participating Member Offline Posts: 24 Joined: Feb 1^st, 2010	Re: RCBS 41-260 FN mold Reply #1 - May 15^th, 2025 at 7:42pm	Print Post
	Another picture.


	IP Logged

axman Participating Member Offline Posts: 24 Joined: Feb 1^st, 2010	Re: RCBS 41-260 FN mold Reply #2 - May 15^th, 2025 at 7:43pm	Print Post
	Top.


	IP Logged

idjeffp Senior Forum Member Offline Posts: 346 Location: Boise, ID Joined: Nov 11^th, 2017	Re: RCBS 41-260 FN mold Reply #3 - May 16^th, 2025 at 2:04pm	Print Post
	Does this cast a .406" bullet for the oldies... or some other size? Thanks, Jeff P


	IP Logged

axman Participating Member Offline Posts: 24 Joined: Feb 1^st, 2010	Re: RCBS 41-260 FN mold Reply #4 - May 16^th, 2025 at 3:35pm	Print Post
	I've read it's a .406" but other forums say some are .410" I've not used it.


	IP Logged

westerner Frequent Elocutionist Offline deleted posts and threads record holder. Posts: 11720 Location: Why, out West of course Joined: May 29^th, 2006	Re: RCBS 41-260 FN mold Reply #5 - May 16^th, 2025 at 4:03pm	Print Post
	Mine casts .406.

	A blind squirrel runs into a tree every once in a while.
	IP Logged

axman Participating Member Offline Posts: 24 Joined: Feb 1^st, 2010	Re: RCBS 41-260 FN mold Reply #6 - May 16^th, 2025 at 4:28pm	Print Post
	I can measure the ID of the base band if that will help. Of course it depends on what alloy.
	« Last Edit: May 16^th, 2025 at 5:48pm by axman »

	IP Logged

axman Participating Member Offline Posts: 24 Joined: Feb 1^st, 2010	Re: RCBS 41-260 FN mold Reply #7 - May 16^th, 2025 at 7:21pm	Print Post
	The ID of the base band hole ID is approximately .407" measured with a set of calipers. I hope this may help?


	IP Logged

idjeffp Senior Forum Member Offline Posts: 346 Location: Boise, ID Joined: Nov 11^th, 2017	Re: RCBS 41-260 FN mold Reply #8 - May 17^th, 2025 at 1:26pm	Print Post
	Thanks axman for checking... Yes, I would need the larger one for my rifles. Jeff P


	IP Logged

axman Participating Member Offline Posts: 24 Joined: Feb 1^st, 2010	Re: RCBS 41-260 FN mold Reply #9 - Jun 1^st, 2025 at 9:10pm	Print Post
	Price drop.


	IP Logged

axman Participating Member Offline Posts: 24 Joined: Feb 1^st, 2010	Re: RCBS 41-260 FN mold Reply #10 - Jun 12^th, 2025 at 7:55am	Print Post
	$110.00


	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 1.3547 seconds.