ASSRA Forum - Low Wall question

ASSRA Forum › General › Single Shot Rifles › Low Wall question

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Normal Topic

Low Wall question (Read 560 times)

fayettefatts Participating Member Online Posts: 21 Joined: Jan 18^th, 2022	Low Wall question Dec 20^th, 2024 at 6:28am	Print Post
	I have a Winchester Low Wall that was produced in 1892 and originally chambered in 22 long. It only extracts and does not eject spent cartridges. Were they made to eject?


	IP Logged

art_ruggiero Frequent Elocutionist Offline Posts: 1120 Location: CT Joined: Dec 14^th, 2008	Re: Low Wall question Reply #1 - Dec 20^th, 2024 at 7:26am	Print Post
	i have a winder musket and it does not eject art


	IP Logged

Old-Win Frequent Elocutionist Offline Posts: 1702 Location: Minnesota Joined: Nov 24^th, 2005	Re: Low Wall question Reply #2 - Dec 20^th, 2024 at 8:51am	Print Post
	Take the forearm off and if you have a lever spring rifle you will see a cutout in the face of the receiver. Just to the right of that cut out will be a smaller cut out where a spring will go and also a screw hole next to it to hold the kicker spring. There are two types of kickers. One type is a solid piece held on by a screw and the other is a bent wire that is held on by a screw. Either one of those can be missing. If it is a coil spring model you will just have the cut out for the kicker spring.


	IP Logged

bpjack Frequent Elocutionist Offline Posts: 2901 Location: East Olympia, WA Joined: May 18^th, 2008	Re: Low Wall question Reply #3 - Dec 20^th, 2024 at 9:22am	Print Post
	The last time this discussion came up, I got out my less than a year old Winder and although all the parts were there, it did not eject. Upon close examination, it turns out the spring was not in the proper position. By loosening the spring and pushing the spring in the right direction it began ejecting. Jack

	ASSRA # 11318 just a bit of a hoot.
	IP Logged

scottz63 Participating Member Offline Posts: 29 Location: Mid Mo Joined: Dec 20^th, 2024	Re: Low Wall question Reply #4 - Dec 20^th, 2024 at 11:09am	Print Post
	My Winder extracts and ejects spent cartridges. It's a coil spring type.

	14EH AIT Instructor-PATRIOT Fire Control Enhanced Operator/Maintainer
	IP Logged

Smoke Oldtimer Offline Posts: 719 Location: San Diego Joined: Feb 24^th, 2013	Re: Low Wall question Reply #5 - Dec 20^th, 2024 at 9:01pm	Print Post
	Not all low walls are winders and not all low walls eject.


	IP Logged

Skalkaho Oldtimer Offline Posts: 796 Location: Montana Joined: Sep 29^th, 2006	Re: Low Wall question Reply #6 - Jan 2^nd, 2025 at 6:08pm	Print Post
	Low wall tweezers...work great ! ebay

	May the Bullet Gods be with you.......
	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2025. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.8648 seconds.