ASSRA Forum - For those who have vision problems

ASSRA Forum › General › General Discussion › For those who have vision problems

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1 [2]

For those who have vision problems (Read 1055 times)

Sure shot Oldtimer Offline Posts: 908 Location: East central Iowa Joined: Jun 22^nd, 2020	Re: For those who have vision problems Reply #15 - Oct 12^th, 2024 at 12:23pm	Print Post
	Unfortunately with my vision problems in my right eye, that's pretty much how crosshairs look to me in a good scope.


	IP Logged

bpjack Frequent Elocutionist Offline Posts: 2780 Location: East Olympia, WA Joined: May 18^th, 2008	Re: For those who have vision problems Reply #16 - Oct 12^th, 2024 at 2:16pm	Print Post
	With .0015 crosshair wire being considered fairly coarse, this wire is .015, a hundred times thicker. Luckily it doesn't appear that there is any glue in the threaded holes. It is a bit thinner than a standard staple shown for comparison.

	ASSRA # 11318 just a bit of a hoot.
	IP Logged

bpjack Frequent Elocutionist Offline Posts: 2780 Location: East Olympia, WA Joined: May 18^th, 2008	Re: For those who have vision problems Reply #17 - Oct 12^th, 2024 at 5:50pm	Print Post
	Bob Siepp resounded that he does not have screws and that he engraves grooves and glues the wire in place. I search through my smallest screws and managed to only find one small enough but not the right pitch. I am going to just glue the wires using the holes for alignment.

	ASSRA # 11318 just a bit of a hoot.
	IP Logged

bpjack Frequent Elocutionist Offline Posts: 2780 Location: East Olympia, WA Joined: May 18^th, 2008	Re: For those who have vision problems Reply #18 - Oct 13^th, 2024 at 5:04pm	Print Post
	I ended up inserting the tip of plastic floss picks which were a nice fit into the holes. That allowed me to use them as posts to use in positioning the wires like you would use a screw shank. Some super glue and I now have some .008' crosshairs. I figure the posts would also prevent any glue from making it into the threads so some future owner could have the crosshairs replaced properly assuming they could source some screws. Jack

	ASSRA # 11318 just a bit of a hoot.
	IP Logged

SBoomer Oldtimer Offline Posts: 957 Location: Michigan's Frozen North (U.P.) Joined: Jan 28^th, 2010	Re: For those who have vision problems Reply #19 - Oct 13^th, 2024 at 7:18pm	Print Post
	Anyone know the size and pitch of these screws?


	IP Logged

bpjack Frequent Elocutionist Offline Posts: 2780 Location: East Olympia, WA Joined: May 18^th, 2008	Re: For those who have vision problems Reply #20 - Oct 13^th, 2024 at 8:13pm	Print Post
	It would be nice to know what size. Here is the scope. There was a yellow filter on the back but no front lens cap. It turns out it takes a standard 52mm camera lens cap. I have a clip on but ordered a screw on one from eBay for $13. Jack

	ASSRA # 11318 just a bit of a hoot.
	IP Logged

Saratoga Bill Participating Member Offline Posts: 40 Location: Saratoga NY or Crystal River F Joined: Oct 18^th, 2016	Re: For those who have vision problems Reply #21 - Oct 14^th, 2024 at 3:48pm	Print Post
	Jack, I have a 30 Unertl with the super fine crosshairs and dot. As you say, they disappear on a black target. They do show good on the scheutzen red targets. Bill


	IP Logged

bpjack Frequent Elocutionist Offline Posts: 2780 Location: East Olympia, WA Joined: May 18^th, 2008	Re: For those who have vision problems Reply #22 - Oct 14^th, 2024 at 4:01pm	Print Post
	Bill, I think I will dedicate this 10x scope to my 32-20 low wall. I hope my eyesight doesn't deteriorate or I will have to add those wires I took off the Unertl.

	ASSRA # 11318 just a bit of a hoot.
	IP Logged

Pages: 1 [2]

‹ Previous Topic | Next Topic ›

Page completed in 1.0532 seconds.