ASSRA Forum › General › Reloading the Single Shot Rifle › WW pure and lead for 20-1 ?
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic WW pure and lead for 20-1 ? (Read 452 times)
Skalkaho
Oldtimer
*****
Offline



Posts: 787
Location: Montana
Joined: Sep 29th, 2006
WW pure and lead for 20-1 ?
Aug 16th, 2024 at 9:56am
Print Post  
Anyone play with WW clip on and pure lead to make 20-1 or 25-1?    I have 500#  of WW all melted down and cleaned comes out about 18-1   .  Normally dont want to put this in my better guns breech seating. Like to hear your  comments.Thankyou.
  
May the Bullet Gods be with you.......
Back to top
 
IP Logged
 
Schuetzendave
Frequent Elocutionist
*****
Offline


Retired Ex-Shooter

Posts: 4046
Location: St. Albert, Alberta
Joined: Jan 28th, 2005
Re: WW pure and lead for 20-1 ?
Reply #1 - Aug 16th, 2024 at 10:09am
Print Post  
I leave the WW to the pistol shooters.

I used alloys when I started that had antimony and always had leading problems.

Switched to pure lead and tin to make 20:1 alloy and had major improvements in eliminating fouling of my rifles.

When WW comes my way I clean it up and sell it to the pistol shooters wanting hard alloys and use the money to buy pure lead and pure tin.
« Last Edit: Aug 16th, 2024 at 5:18pm by Schuetzendave »  
Back to top
 
IP Logged
 
beltfed
Frequent Elocutionist
*****
Offline



Posts: 1752
Location: Central Wi
Joined: Dec 20th, 2007
Re: WW pure and lead for 20-1 ?
Reply #2 - Aug 16th, 2024 at 12:00pm
Print Post  
18:1.  Do you mean the Hardness of 18:1?
This as is will not breech seat easily.  
I would suggest start with   25 lead plus 1 COWW

Remember, the COWW is approximately 4% or so of Antimony.
AND almost No tin.
So, to make the alloy cast well, add 1% tin added to the 
25lead plus 1 COWW

And, note that CLEANED COWW will not harm your rifles.

I have used my alloy of 9+1  COWW/Lino for many years
and have had no problem with leading, as long as the 
bullet diameter is 0.001 over groove diameter and use a good
lube. This applies to my Schuetzen rifles(not breechseated) and also BPCR rifles
velocities up to at least 1700fps.
For breechseating my 25-20, I do use 20+1 lead/tin.
beltfed/arnie
« Last Edit: Aug 16th, 2024 at 12:05pm by beltfed »  
Back to top
 
IP Logged
 
Skalkaho
Oldtimer
*****
Offline



Posts: 787
Location: Montana
Joined: Sep 29th, 2006
Re: WW pure and lead for 20-1 ?
Reply #3 - Aug 16th, 2024 at 3:09pm
Print Post  
Spaced out guys...hardness same as 18-1. I think it best to sell it off and stay with pure lead and tin.  Appreciate guys.Pete
  
May the Bullet Gods be with you.......
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.6980 seconds.