ASSRA Forum - Barrel clamp or sled

ASSRA Forum › General › Single Shot Rifles › Barrel clamp or sled

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: [1] 2

Hot Topic (More than 10 Replies)

Barrel clamp or sled (Read 1327 times)

Oakdale Participating Member Offline Posts: 33 Location: Maplewood, MN Joined: Jun 7^th, 2017	Barrel clamp or sled Aug 3^rd, 2024 at 3:33pm	Print Post
	My Remington Rolling Block has a Green Mountain heavy, full octagon barrel. Chambering is .38-55. I've tried heavy gasket material and also deer hide (not together) as the buffer material between the barrel and the clamp. But the clamp slowly creeps forward with each shot. The deer hide works marginally better. One shooter today had just a strip of target paper in between the two surfaces. Is there a better buffer material that I should try? Thanks! Tom


	IP Logged

JerryH Frequent Elocutionist Offline ASSRA Member #10876 Posts: 1241 Location: Easton, CA Joined: Nov 9^th, 2014	Re: Barrel clamp or sled Reply #1 - Aug 3^rd, 2024 at 3:39pm	Print Post
	I use a piece of bicycle inner tube.

	I'm not a complete idiot, some of my parts are missing.
	IP Logged

Jeff_Schultz ASSRA Board Member Online Posts: 1606 Location: Ransomville, NY Joined: Apr 25^th, 2004	Re: Barrel clamp or sled Reply #2 - Aug 3^rd, 2024 at 4:22pm	Print Post
	Put a little rosin on it.

	"We have met the enemy and he is us." Pogo “There is no situation so bad that it cannot be made worse." Confidence- The feeling you get before you fully understand the situation.
	IP Logged

Oakdale Participating Member Offline Posts: 33 Location: Maplewood, MN Joined: Jun 7^th, 2017	Re: Barrel clamp or sled Reply #3 - Aug 3^rd, 2024 at 4:28pm	Print Post
	That tire rubber should work better. Worth a try. I'll track some down. Thanks! Tom


	IP Logged

Liveoak Participating Member Offline Posts: 16 Location: Texas Hill Country Joined: May 4^th, 2019	Re: Barrel clamp or sled Reply #4 - Aug 3^rd, 2024 at 10:15pm	Print Post
	I get mine from the local bike shop; their used tubes just go into the trash, anyway. Cut across the tube they make great bands to hold mould blocks together, too! FCH


	IP Logged

RSW Frequent Elocutionist Offline Posts: 1188 Location: Arizona Joined: Sep 8^th, 2006	Re: Barrel clamp or sled Reply #5 - Aug 4^th, 2024 at 2:34pm	Print Post
	For the many years that I have used a "sled" I have used strips of cardboard cut from cereal boxes. About an inch wide and just long enough to be grabbed by the sled clamps. Round or octagon barrels, works great. Had a physicist tell me one time that the grip between cardboard and the steel barrel is VERY slip resistant. I cut a number of those strips and used each for a couple of shooting sessions then toss them for a new one.

	Randy W ASSRA 10211 - ISSA 125 There are indeed two Americas. Simply put, it is not the haves and have nots. The two Americans are in reality divided into those who do and those who don't.
	WWW IP Logged

JHand Junior Member Offline Posts: 50 Joined: Apr 15^th, 2024	Re: Barrel clamp or sled Reply #6 - Aug 4^th, 2024 at 5:16pm	Print Post
	Given, I just built mine, but I wrapped the contact points of my sled with thick electrical tape and it doesn't move


	IP Logged

SBoomer Oldtimer Offline Posts: 954 Location: Michigan's Frozen North (U.P.) Joined: Jan 28^th, 2010	Re: Barrel clamp or sled Reply #7 - Aug 4^th, 2024 at 5:32pm	Print Post
	Like Randy, I use cardboard. I cut mine from the back of notepaper pads…..its a little thicker than cereal box cardboard. I dont think you will be happy with the electrical tape. I’d be really surprised if it doesn't slip.


	IP Logged

Schuetzendave Frequent Elocutionist Offline Retired Ex-Shooter Posts: 4045 Location: St. Albert, Alberta Joined: Jan 28^th, 2005	Re: Barrel clamp or sled Reply #8 - Aug 4^th, 2024 at 6:41pm	Print Post
	Plain old sandbag has worked extremely well for me over the years. Never bothered with a sled.


	IP Logged

JHand Junior Member Offline Posts: 50 Joined: Apr 15^th, 2024	Re: Barrel clamp or sled Reply #9 - Aug 4^th, 2024 at 6:54pm	Print Post
	SBoomer wrote on Aug 4^th, 2024 at 5:32pm: Like Randy, I use cardboard. I cut mine from the back of notepaper pads…..its a little thicker than cereal box cardboard. I dont think you will be happy with the electrical tape. I’d be really surprised if it doesn't slip. Guess I should clarify, from my days in construction, we had 2 grades of electrical tape: cheap tape, and expensive tape. Most people get the cheap stuff, which would not work. The stuff that is $6-$10 per roll is much thicker, and is almost rubber. That's the stuff I'm using. I've shot on the sled 4-5 times since building, and it hasn't moved yet. I may end up with the in er tube, but just used what I had on hand to start with
	« Last Edit: Aug 4^th, 2024 at 8:37pm by JHand »

	IP Logged

gnoahhh Oldtimer Offline Posts: 809 Location: Gaithersburg, MD Joined: Mar 31^st, 2010	Re: Barrel clamp or sled Reply #10 - Aug 4^th, 2024 at 9:12pm	Print Post
	I've been threatening to give old fashioned cloth backed friction tape a whirl. You know, the gummy thick nasty stuff that our Gramps and Dads had in the bottom of their rusty tool boxes, the stuff they used to bind up a hole in the washing machine hose or a leaky radiator hose in the Ford in order to make it home from church. Slapdash attempts to find The Real McCoy haven't turned any up yet.


	IP Logged

SBoomer Oldtimer Offline Posts: 954 Location: Michigan's Frozen North (U.P.) Joined: Jan 28^th, 2010	Re: Barrel clamp or sled Reply #11 - Aug 5^th, 2024 at 9:47am	Print Post
	gnoahhh wrote on Aug 4^th, 2024 at 9:12pm: I've been threatening to give old fashioned cloth backed friction tape a whirl. You know, the gummy thick nasty stuff that our Gramps and Dads had in the bottom of their rusty tool boxes, the stuff they used to bind up a hole in the washing machine hose or a leaky radiator hose in the Ford in order to make it home from church. Slapdash attempts to find The Real McCoy haven't turned any up yet. You made me chuckle. Sadly replaced by Gorilla tape.


	IP Logged

SBoomer Oldtimer Offline Posts: 954 Location: Michigan's Frozen North (U.P.) Joined: Jan 28^th, 2010	Re: Barrel clamp or sled Reply #12 - Aug 5^th, 2024 at 9:50am	Print Post
	Ill be darned…..its still made! (You need to *Login* or *Register* to view media files and links)


	IP Logged

Dellet Frequent Elocutionist Offline Posts: 1090 Joined: May 19^th, 2017	Re: Barrel clamp or sled Reply #13 - Aug 5^th, 2024 at 10:10am	Print Post
	Friction tape generally only sticks best to itself, unless you can get a wrap it may not hold well. Hockey tape might be better choice.


	IP Logged

gnoahhh Oldtimer Offline Posts: 809 Location: Gaithersburg, MD Joined: Mar 31^st, 2010	Re: Barrel clamp or sled Reply #14 - Aug 5^th, 2024 at 12:01pm	Print Post
	SBoomer wrote on Aug 5^th, 2024 at 9:50am: Ill be darned…..its still made! (You need to *Login* or *Register* to view media files and links) Well I'll be. Thanks! I ordered a roll.


	IP Logged

Page Index Toggle

Pages: [1] 2

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 1.0090 seconds.