ASSRA Forum - Ideal mould 373165

ASSRA Forum › General › Reloading the Single Shot Rifle › Ideal mould 373165

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Normal Topic

Ideal mould 373165 (Read 432 times)

Babydriver Participating Member Offline Posts: 27 Joined: Mar 22^nd, 2024	Ideal mould 373165 Jul 25^th, 2024 at 9:18pm	Print Post
	Looking for an ideal /lyman 373165 mould. Thanks


	IP Logged

Green_Frog Frequent Elocutionist Offline "It ain't easy being green" ASSRA Life #281 Posts: 3996 Location: Lynchburg, VA Joined: Apr 18^th, 2004	Re: Ideal mould 373165 Reply #1 - Jul 26^th, 2024 at 4:08pm	Print Post
	??? Are you sure it wasn’t a 375165? I can’t remember ever seeing a 373 anything. What do you know about it and what is the application? Froggie


	IP Logged

Babydriver Participating Member Offline Posts: 27 Joined: Mar 22^nd, 2024	Re: Ideal mould 373165 Reply #2 - Jul 26^th, 2024 at 5:47pm	Print Post
	Well frog, the ideal handbook #15, page 108 says “ 373165 is the standard bullet for the 38-40 and 38-50 Remington. It goes on to say that .373 (.38-45, 38-50 REM and 38-45 Bullard ). I have a 38-45 Bullard and I have the 38-45 190 373164 mould. I have shot the 190 gr over 16 gh 4198 and and a 375248 250 gn over 16 gn 4198 and surprisingly they both chronographed about the same. 1300 fps. So still looking for the 373165. 👍👍


	IP Logged

Babydriver Participating Member Offline Posts: 27 Joined: Mar 22^nd, 2024	Re: Ideal mould 373165 Reply #3 - Jul 26^th, 2024 at 5:52pm	Print Post
	I forgot to say that it’s for a Remington Hepburn, 38-40 Remington, double set trigger, case colored, and in Winchester barrel weights #5.


	IP Logged

Green_Frog Frequent Elocutionist Offline "It ain't easy being green" ASSRA Life #281 Posts: 3996 Location: Lynchburg, VA Joined: Apr 18^th, 2004	Re: Ideal mould 373165 Reply #4 - Jul 27^th, 2024 at 1:09pm	Print Post
	“Open mouth, insert foot.” I saw those numbers and immediately thought “38-55”. Mea culpa, but at least it kept your thread active! I wish you luck in your search because that Hepburn should be a hoot to shoot. You may find it worth your while to have one of the custom mould makers cut one for you. I’ve played the game chasing discontinued Ideal moulds and the hunt was fun but cut down on my shooting time. Regards, Froggie


	IP Logged

Babydriver Participating Member Offline Posts: 27 Joined: Mar 22^nd, 2024	Re: Ideal mould 373165 Reply #5 - Jul 27^th, 2024 at 2:53pm	Print Post
	I share your frustration. But sometimes it’s does pay off. Thanks


	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.8437 seconds.