ASSRA Forum - A Burgeoning Interest in the Husqvarna No 33

ASSRA Forum › General › Collecting Single Shot Rifles › A Burgeoning Interest in the Husqvarna No 33

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: [1] 2

Very Hot Topic (More than 25 Replies)

A Burgeoning Interest in the Husqvarna No 33 (Read 2984 times)

S99VG Oldtimer Offline Posts: 509 Location: CA Joined: Feb 1^st, 2020	A Burgeoning Interest in the Husqvarna No 33 Feb 16^th, 2023 at 10:18am	Print Post
	I am a Stevens guy to the core however I have always had an eye on rolling blocks. Last night while crusing the gun auction and sale sites I stumbled on a Husqvarna No 33 in 8x57R/360 and became a bit smitten. I don't see these rifles talked about too around here and perhaps this forum doesn't quite fit their their niche, but if anyone would like to share some information I would appreciate leaning more about these rifles and the cartridge. Many thanks in advance for the education!


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 16268 Location: Oregon Joined: Feb 2^nd, 2009	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #1 - Feb 16^th, 2023 at 12:12pm	Print Post
	The Husqvarna 33 has spurred several lengthy conversations here in the past, and several fellas have them here. Mine is in 9.5x47R which is almost identical to .38-55, just slightly shorter, and uses a .376" bullet. I really love Rolling Blocks, and the Type 33A is as good as any Remington, and a lot sleeker, and cooler receiver contours. (You need to *Login* or *Register* to view media files and links) (You need to *Login* or *Register* to view media files and links)

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

Rebel Frequent Elocutionist Offline Posts: 4292 Location: Rockets and Race Cars Joined: Mar 9^th, 2015	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #2 - Feb 16^th, 2023 at 12:22pm	Print Post
	I spy an unusual tang sight on that 33, what did you install? Aaron

	WARNING: This post may contain material offensive to those who lack wit, humor, common sense and supporting factual or anecdotal evidence. Let's Go Sonny!
	IP Logged

S99VG Oldtimer Offline Posts: 509 Location: CA Joined: Feb 1^st, 2020	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #3 - Feb 16^th, 2023 at 12:23pm	Print Post
	Damn, that’s nice!


	IP Logged

oneatatime Frequent Elocutionist Offline Posts: 3912 Location: Rocky Mountains Joined: Oct 30^th, 2011	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #4 - Feb 16^th, 2023 at 4:43pm	Print Post
	Here are the two I've had, both in 9.3x57R (360) Still have the full stock.


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 16268 Location: Oregon Joined: Feb 2^nd, 2009	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #5 - Feb 16^th, 2023 at 4:46pm	Print Post
	Rebel wrote on Feb 16^th, 2023 at 12:22pm: I spy an unusual tang sight on that 33, what did you install? Aaron That is what Marbles called their "Special Flexible Base" tang sight. I found the factory express sight on the barrel wasn't easy to get a good sight picture.

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

oneatatime Frequent Elocutionist Offline Posts: 3912 Location: Rocky Mountains Joined: Oct 30^th, 2011	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #6 - Feb 16^th, 2023 at 4:54pm	Print Post
	My full stock just has a plain old Marbles tang sight. There is a little trick in mounting them as there is built-in cast off in the tangs.


	IP Logged

S99VG Oldtimer Offline Posts: 509 Location: CA Joined: Feb 1^st, 2020	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #7 - Feb 16^th, 2023 at 6:52pm	Print Post
	oneatatime wrote on Feb 16^th, 2023 at 4:54pm: My full stock just has a plain old Marbles tang sight. There is a little trick in mounting them as there is built-in cast off in the tangs. That’s interesting


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 16268 Location: Oregon Joined: Feb 2^nd, 2009	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #8 - Feb 17^th, 2023 at 11:00am	Print Post
	oneatatime wrote on Feb 16^th, 2023 at 4:54pm: My full stock just has a plain old Marbles tang sight. There is a little trick in mounting them as there is built-in cast off in the tangs. Now I need to look at mine again? Never noticed the cast off, so I mounted mine centered on the top tang, and seems to be OK. I did notice the top tang wasn't perfectly shaped, and I used a shim under the left side of the base to get it perfectly upright.

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

S99VG Oldtimer Offline Posts: 509 Location: CA Joined: Feb 1^st, 2020	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #9 - Feb 17^th, 2023 at 12:10pm	Print Post
	marlinguy wrote on Feb 17^th, 2023 at 11:00am: oneatatime wrote on Feb 16^th, 2023 at 4:54pm: My full stock just has a plain old Marbles tang sight. There is a little trick in mounting them as there is built-in cast off in the tangs. Now I need to look at mine again? Never noticed the cast off, so I mounted mine centered on the top tang, and seems to be OK. I did notice the top tang wasn't perfectly shaped, and I used a shim under the left side of the base to get it perfectly upright. That must play heck with left handed shooters?


	IP Logged

oneatatime Frequent Elocutionist Offline Posts: 3912 Location: Rocky Mountains Joined: Oct 30^th, 2011	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #10 - Feb 17^th, 2023 at 12:22pm	Print Post
	It is so slight that you might not even notice it. I certainly didn't until my super precise gunsmith who mounted the sight pointed it out. I guess most of the Swedes are right handed;-) Also note that they were made from 1877 until 1912 although I think most dealers would treat them as antiques (no list of serial numbers/years). Here's all the Huskys (You need to *Login* or *Register* to view media files and links). Note all the possible calibers (except for Vall's). They seldom come up for sale these days so if you see one you should grab it.


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 16268 Location: Oregon Joined: Feb 2^nd, 2009	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #11 - Feb 17^th, 2023 at 12:31pm	Print Post
	Actually my cartridge is listed on the site among the Studsare Nr33 cartridges. "6x36R / 6.5x42R / 8x42R / 8x57R/360 / 9x47R / 9.3x57R/360 / 9.5x47R / 10x47R / 10,5x47R"

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

oneatatime Frequent Elocutionist Offline Posts: 3912 Location: Rocky Mountains Joined: Oct 30^th, 2011	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #12 - Feb 17^th, 2023 at 1:21pm	Print Post
	I originally had my doubts about that one because the most common 9.5x47R is a bottlenecked target cartridge and a shortened 38-55 would not have worked in that chamber, but I have just discovered that in the 1880s when the nomenclature "9.5x47R" was first in use there were at least 8 varieties of it. I have ordered a book that should give more complete information about these varieties and pinpoint the origin of Vall's.


	IP Logged

marlinguy Frequent Elocutionist Offline Ballards may be weaker, but they sure are neater! Posts: 16268 Location: Oregon Joined: Feb 2^nd, 2009	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #13 - Feb 18^th, 2023 at 11:42am	Print Post
	My original search result was Cartridges of the World, but I didn't trust that source as it's been sketchy often. My chamber looks unmessed with, and the bottleneck version COTW showed is a larger base and rim diameter, so it couldn't be rechambered to what mine is. So I'm pretty confident that my straight wall chamber is original to this gun.

	(You need to *Login* or *Register* to view media files and links)
	IP Logged

S99VG Oldtimer Offline Posts: 509 Location: CA Joined: Feb 1^st, 2020	Re: A Burgeoning Interest in the Husqvarna No 33 Reply #14 - Feb 18^th, 2023 at 12:41pm	Print Post
	How is this source for brass? (You need to *Login* or *Register* to view media files and links)


	IP Logged

Page Index Toggle

Pages: [1] 2

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.6364 seconds.