ASSRA Forum - .25-25 #2 rolling block

ASSRA Forum › General › Reloading the Single Shot Rifle › .25-25 #2 rolling block - separated case neck!

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1 2 [3]

.25-25 #2 rolling block - separated case neck! (Read 2525 times)

Sure shot Oldtimer Offline Posts: 904 Location: East central Iowa Joined: Jun 22^nd, 2020	Re: .25-25 #2 rolling block - separated case neck! Reply #30 - Jan 2^nd, 2023 at 7:21pm	Print Post
	Jess will do a .32-20 rebore, just call and ask. I have had him do two .32-20 rebores for me, one about a year ago for a Stevens 44 that I chambered for .32 S&W long. You could also consider a rebore to .38 special for your #2 rolling block.


	IP Logged

ndnchf Frequent Elocutionist Online Posts: 1044 Joined: Mar 6^th, 2014	Re: .25-25 #2 rolling block - separated case neck! Reply #31 - Jan 2^nd, 2023 at 7:40pm	Print Post
	Sure shot wrote on Jan 2^nd, 2023 at 7:21pm: You could also consider a rebore to .38 special for your #2 rolling block. I thought of that, but the FUBAR'd chamber is way longer than .38 Special. No way to do it without setting the barrel back a lot. I don't want to do that.


	IP Logged

Dellet Frequent Elocutionist Offline Posts: 1089 Joined: May 19^th, 2017	Re: .25-25 #2 rolling block - separated case neck! Reply #32 - Jan 2^nd, 2023 at 7:57pm	Print Post
	ndnchf wrote on Jan 2^nd, 2023 at 7:40pm: Sure shot wrote on Jan 2^nd, 2023 at 7:21pm: You could also consider a rebore to .38 special for your #2 rolling block. I thought of that, but the FUBAR'd chamber is way longer than .38 Special. No way to do it without setting the barrel back a lot. I don't want to do that. Everything in in front of the shoulder of the 25-20 Will be a lot smaller than .345”. You should have about .200” to spare if your measurements to the shoulder were reasonably close. The 25-25 portion thats left will be well below.300” Unless they did a 25-20 Ackley you should be fine.


	IP Logged

ndnchf Frequent Elocutionist Online Posts: 1044 Joined: Mar 6^th, 2014	Re: .25-25 #2 rolling block - separated case neck! Reply #33 - Jan 3^rd, 2023 at 10:18am	Print Post
	Dellet wrote on Jan 2^nd, 2023 at 7:57pm: ndnchf wrote on Jan 2^nd, 2023 at 7:40pm: Sure shot wrote on Jan 2^nd, 2023 at 7:21pm: You could also consider a rebore to .38 special for your #2 rolling block. I thought of that, but the FUBAR'd chamber is way longer than .38 Special. No way to do it without setting the barrel back a lot. I don't want to do that. Everything in in front of the shoulder of the 25-20 Will be a lot smaller than .345”. You should have about .200” to spare if your measurements to the shoulder were reasonably close. The 25-25 portion thats left will be well below.300” Unless they did a 25-20 Ackley you should be fine. Good point. That does open up other possibilities - including .38WCF and .44WCF, which were original Remington chamberings in #2 rifles.


	IP Logged

Dellet Frequent Elocutionist Offline Posts: 1089 Joined: May 19^th, 2017	Re: .25-25 #2 rolling block - separated case neck! Reply #34 - Jan 3^rd, 2023 at 12:38pm	Print Post
	Do a casting and sit down with the SAAMI chamber drawings. A 32-20 might even work, but I think it has more taper than the 25-20 and Is smaller where the 25-20 shoulder starts. I think you have a lot of options. You could always make a sleeve of sorts like your 25 rf charged with a 22 blank. Stick a 25-25 case in 25-20 shaped body. Or a 28-30 ran through a 25-20 die


	IP Logged

Pages: 1 2 [3]

‹ Previous Topic | Next Topic ›

Page completed in 0.7337 seconds.