ASSRA Forum - Need Help Identifying this luber

ASSRA Forum › General › Reloading the Single Shot Rifle › Need Help Identifying this luber

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1

Need Help Identifying this luber (Read 606 times)

jeffer1942 Senior Forum Member ASSRA Target Sales Online Posts: 282 Location: Chicago North suburb Joined: May 31^st, 2004	Need Help Identifying this luber Aug 20^th, 2022 at 2:03pm	Print Post
	The only markings are what I assume is the serial # (28)...no name. Came with 3 inserts, .262, .324, .510


	IP Logged

rgchristensen Frequent Elocutionist Offline Posts: 1091 Joined: Jan 2^nd, 2014	Re: Need Help Identifying this luber Reply #1 - Aug 20^th, 2022 at 2:21pm	Print Post
	Looks like a Charlie Dell style luber, so probably made by CED or perhaps Willis Gregory. Haven't seen one with a square section on the tube before. If it is a CED, it should have an acorn stamped on it somewhere. They are amongst the best of these devices. The only thing I would change is to have a circular knob instead of a cross-handle to squirt out the lube. Serial #s on the Dell lubers ran up over 100 -- don't know if Willis continued the numbers or started again. CHRIS


	IP Logged

ledball Frequent Elocutionist Offline Posts: 1010 Location: syracuse, ohio Joined: Nov 20^th, 2009	Re: Need Help Identifying this luber Reply #2 - Aug 20^th, 2022 at 2:22pm	Print Post
	Appears to be a Charlie Dell lube pump. Ledball


	IP Logged

jeffer1942 Senior Forum Member ASSRA Target Sales Online Posts: 282 Location: Chicago North suburb Joined: May 31^st, 2004	Re: Need Help Identifying this luber Reply #3 - Aug 20^th, 2022 at 2:34pm	Print Post
	Thanks! The "square" section is actually round and finely knurled....


	IP Logged

rgchristensen Frequent Elocutionist Offline Posts: 1091 Joined: Jan 2^nd, 2014	Re: Need Help Identifying this luber Reply #4 - Aug 20^th, 2022 at 5:34pm	Print Post
	jeffer1942 wrote on Aug 20^th, 2022 at 2:34pm: Thanks! The "square" section is actually round and finely knurled.... I see now -- I was wondering where the "usual" knurling was...... CHRIS


	IP Logged

ledball Frequent Elocutionist Offline Posts: 1010 Location: syracuse, ohio Joined: Nov 20^th, 2009	Re: Need Help Identifying this luber Reply #5 - Aug 20^th, 2022 at 7:13pm	Print Post
	If it was made by C Dell it probably has a little mark on it that looks like an acorn but is really a chinquapin. Ledball


	IP Logged

JLouis Frequent Elocutionist Offline Posts: 10625 Joined: Apr 8^th, 2009	Re: Need Help Identifying this luber Reply #6 - Aug 20^th, 2022 at 7:22pm	Print Post
	My Dell / Gregory Lube Pump ? is Numbered D152.

	" It Is Better To Now Have Been A Has Been Than A Never Was Or A Wanna Be "
	IP Logged

Green_Frog Frequent Elocutionist Offline "It ain't easy being green" ASSRA Life #281 Posts: 4023 Location: Lynchburg, VA Joined: Apr 18^th, 2004	Re: Need Help Identifying this luber Reply #7 - Aug 20^th, 2022 at 8:53pm	Print Post
	It surely looks like on of Charlie's to me. Charlie insisted on that fine knurling. Does the unit in question have a serial number and/or other stamping on the aluminum body tube close to one end? Froggie


	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

Page completed in 1.0663 seconds.