ASSRA Forum - Can anyone ID this lever?

ASSRA Forum › General › General Discussion › Can anyone ID this lever?

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Pages: 1

Can anyone ID this lever? (Read 1116 times)

bpjack Frequent Elocutionist Offline Posts: 2793 Location: East Olympia, WA Joined: May 18^th, 2008	Can anyone ID this lever? May 27^th, 2021 at 8:04pm	Print Post
	Picked this finger lever up on eBay. It was listed as a Winchester 1885 Lever but is different from any that I have seen. The nose is not the same as my flat spring ones and as shown overlayed on a standard lever it would not close all the way. Thanks Jack

	ASSRA # 11318 just a bit of a hoot.
	IP Logged

JerryH Frequent Elocutionist Offline ASSRA Member #10876 Posts: 1241 Location: Easton, CA Joined: Nov 9^th, 2014	Re: Can anyone ID this lever? Reply #1 - May 27^th, 2021 at 8:12pm	Print Post
	Falling Block Works Model J. JerryH

	I'm not a complete idiot, some of my parts are missing.
	IP Logged

John Boy Ex Member	Re: Can anyone ID this lever? Reply #2 - May 27^th, 2021 at 8:13pm	Print Post
	Jack, know anyone close to you that has a copy of Frank’s Single Shot Rifles and Actions.... plenty diagrams (You need to *Login* or *Register* to view media files and links)


	IP Logged

JLouis Frequent Elocutionist Offline Posts: 10625 Joined: Apr 8^th, 2009	Re: Can anyone ID this lever? Reply #3 - May 27^th, 2021 at 8:14pm	Print Post
	Jack that one is very similar to the casting that I gifted to Vall / Marlinguy for one of his Ballard restoration's.

	" It Is Better To Now Have Been A Has Been Than A Never Was Or A Wanna Be "
	IP Logged

JLouis Frequent Elocutionist Offline Posts: 10625 Joined: Apr 8^th, 2009	Re: Can anyone ID this lever? Reply #4 - May 27^th, 2021 at 8:21pm	Print Post
	JerryH might be right as it is also very similar to my Model J FBW's three finger Pope lever.

	" It Is Better To Now Have Been A Has Been Than A Never Was Or A Wanna Be "
	IP Logged

JerryH Frequent Elocutionist Offline ASSRA Member #10876 Posts: 1241 Location: Easton, CA Joined: Nov 9^th, 2014	Re: Can anyone ID this lever? Reply #5 - May 27^th, 2021 at 8:23pm	Print Post
	Definitely not a Ballard, and I'm not guessing on the FBW Model J. About 99% sure as I've see the one you have JLouis. The cut-out for the extractor is the giveaway. JerryH

	I'm not a complete idiot, some of my parts are missing.
	IP Logged

bpjack Frequent Elocutionist Offline Posts: 2793 Location: East Olympia, WA Joined: May 18^th, 2008	Re: Can anyone ID this lever? Reply #6 - May 27^th, 2021 at 8:39pm	Print Post
	I thought Ballard as well due to the extractor cut out but not even close to fitting. The seller advertises that he will refund for any reason. I suppose I could see if anyone here would be interested in a model J lever before I request a refund. Thanks Jack

	ASSRA # 11318 just a bit of a hoot.
	IP Logged

JerryH Frequent Elocutionist Offline ASSRA Member #10876 Posts: 1241 Location: Easton, CA Joined: Nov 9^th, 2014	Re: Can anyone ID this lever? Reply #7 - May 27^th, 2021 at 9:21pm	Print Post
	bpjack wrote on May 27^th, 2021 at 8:39pm: I thought Ballard as well due to the extractor cut out but not even close to fitting. The seller advertises that he will refund for any reason. I suppose I could see if anyone here would be interested in a model J lever before I request a refund. Thanks Jack A relatively rare lever. Someone on the forum would likely be pleased to have it. JerryH

	I'm not a complete idiot, some of my parts are missing.
	IP Logged

Pages: 1

‹ Previous Topic | Next Topic ›

Page completed in 1.2501 seconds.