ASSRA Forum › General › General Discussion › Ballard questions
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 Send TopicPrint
Normal Topic Ballard questions (Read 1548 times)
bpjack
Frequent Elocutionist
*****
Offline



Posts: 2793
Location: East Olympia, WA
Joined: May 18th, 2008
Ballard questions
May 3rd, 2021 at 1:40pm
Print Post  
I have a few more questions about my chrome Ballard.  There are the two holes in the action face where pins are on my Pacific.  Were these present on different models?  There s also a shallow hole on the bottom of the action.  Any idea why?  It is not very deep as evidenced by the screw next to it.
The action is also missing the fly so no 1/2 cock (which I don't use anyway).  I found one at the Rifle Shoppe.  Does anyone know if they are still in business?

Thanks

Jack
  
ASSRA # 11318
just a bit of a hoot.
Back to top
 
IP Logged
 
830singleshot
Senior Forum Member
****
Offline



Posts: 404
Location: Texas
Joined: Feb 11th, 2007
Re: Ballard questions
Reply #1 - May 3rd, 2021 at 1:57pm
Print Post  
Judging by the mark on the lever from the screw, my guess is the screw was added to limit the extractor travel.
  
J. Scott McCash&&New Braunfels, TX&&830-237-2376&&jsmccash@yahoo.com
Back to top
 
IP Logged
 
JLouis
Frequent Elocutionist
*****
Offline



Posts: 10625
Joined: Apr 8th, 2009
Re: Ballard questions
Reply #2 - May 3rd, 2021 at 2:02pm
Print Post  
Interesting observation are Ballards know for having the case rim going past the extractor with some cases.
  
" It Is Better To Now Have Been A Has Been Than A Never Was Or A Wanna Be "
Back to top
 
IP Logged
 
bpjack
Frequent Elocutionist
*****
Offline



Posts: 2793
Location: East Olympia, WA
Joined: May 18th, 2008
Re: Ballard questions
Reply #3 - May 3rd, 2021 at 3:42pm
Print Post  
Good observation.  That does seem to be the case.  The screw limits both the extractor travel and the hammer height when the lever is fully open. 

Jack
  
ASSRA # 11318
just a bit of a hoot.
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 16157
Location: Oregon
Joined: Feb 2nd, 2009
Re: Ballard questions
Reply #4 - May 3rd, 2021 at 6:08pm
Print Post  
JLouis wrote on May 3rd, 2021 at 2:02pm:
Interesting observation are Ballards know for having the case rim going past the extractor with some cases.


No they are not. But often times odd hard to find brass requires you to substitute a donor brass that has a little smaller rim. This will result in needing to be careful when chambering to ensure the rim stays behind the extractor. Not an issue isolated to Ballard rifles, but something fairly common with any cartridge not easy to find brass for.
Another issue is when people build Ballard rifles from actions and extractors designed for CF cartridges, but use that type extractor for .22RF cartridges. The arc of the extractor's travel often makes a situation where it loses contact with a small .22rf rim, and then too the case can slip past.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 16157
Location: Oregon
Joined: Feb 2nd, 2009
Re: Ballard questions
Reply #5 - May 3rd, 2021 at 6:12pm
Print Post  
bpjack wrote on May 3rd, 2021 at 1:40pm:
I have a few more questions about my chrome Ballard.  There are the two holes in the action face where pins are on my Pacific.  Were these present on different models?  There s also a shallow hole on the bottom of the action.  Any idea why?  It is not very deep as evidenced by the screw next to it.
The action is also missing the fly so no 1/2 cock (which I don't use anyway).  I found one at the Rifle Shoppe.  Does anyone know if they are still in business?

Thanks

Jack


Ballard rifles usually have the two holes for pins on a Pacific, but only have the pins if they are a Pacific, Montana, or the 4 3/4 single trigger Pacific models.
Not sure why your action has two holes by the lever, but as 830singleshot mentioned it appears to be a lever stop. Not sure why it would need one, as I've never seen this before.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
westerner
Frequent Elocutionist
*****
Offline


deleted posts and threads
record holder.

Posts: 11474
Location: Why, out West of course
Joined: May 29th, 2006
Re: Ballard questions
Reply #6 - May 4th, 2021 at 1:28pm
Print Post  
Two of my Ballards are easy to get the rim behind the extractor. Easy to do when the extractor comes way back.
  
A blind squirrel runs into a tree every once in a while.
Back to top
 
IP Logged
 
bohemianway
Oldtimer
*****
Offline



Posts: 646
Location: Andover, MN
Joined: Apr 16th, 2004
Re: Ballard questions
Reply #7 - May 4th, 2021 at 4:40pm
Print Post  
Forty years ago I got bit by a Pope Highwall .22RF when the rim slipped past the extractor. On closing the action it set off the cartridge before the block got behind the case. I literally saw the case backing out of the chamber before it came apart and filled my face with shrapnel. I wouldn't recommend it.

Charles
  
Back to top
GTalk  
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 16157
Location: Oregon
Joined: Feb 2nd, 2009
Re: Ballard questions
Reply #8 - May 4th, 2021 at 8:42pm
Print Post  
bohemianway wrote on May 4th, 2021 at 4:40pm:
Forty years ago I got bit by a Pope Highwall .22RF when the rim slipped past the extractor. On closing the action it set off the cartridge before the block got behind the case. I literally saw the case backing out of the chamber before it came apart and filled my face with shrapnel. I wouldn't recommend it.

Charles


Quite common when a CF is converted to .22RF and the CF extractor is used. I've got three Ballard schuetzen rifles that started out as CF actions, and converted to .22RF, and need to watch them carefully when loading.
But I have four #3 with 2 piece sliding factory extractors, and they never slip past when loading. The straight sliding extractors work very well.
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
bohemianway
Oldtimer
*****
Offline



Posts: 646
Location: Andover, MN
Joined: Apr 16th, 2004
Re: Ballard questions
Reply #9 - May 4th, 2021 at 9:07pm
Print Post  
I only have one #3 and the one #3PG both with two piece and they are a charm. I relined the #3 and it is a tedious job boring the hole for it when the liner cuts half way into it.
  
Back to top
GTalk  
IP Logged
 
Page Index Toggle Pages: 1
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 1.2519 seconds.