ASSRA Forum › General › Reloading the Single Shot Rifle › Martini Cadet 32-357- need help
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: 1 [2]  Send TopicPrint
Hot Topic (More than 10 Replies) Martini Cadet 32-357- need help (Read 5442 times)
Longdistance1
Senior Forum Member
****
Offline



Posts: 429
Location: Amidon, ND
Joined: Feb 11th, 2013
Re: Martini Cadet 32-357- need help
Reply #15 - Oct 11th, 2020 at 1:37pm
Print Post  
Phil, I used a IPCO graphite grease wad over the corn meal, if I had a hot glue gun that would be better as the IPCO wad and the cornmeal made mess in the bore.  Any wad to keep the cornmeal from spilling into the chamber will work fine.
  
Back to top
 
IP Logged
 
oneatatime
Frequent Elocutionist
*****
Offline



Posts: 3866
Location: Rocky Mountains
Joined: Oct 30th, 2011
Re: Martini Cadet 32-357- need help
Reply #16 - Oct 11th, 2020 at 1:54pm
Print Post  
I just flattened part of an old lube stick between two sheets of wax paper using a rolling pin and just pressed the thin lube down over the case mouth and Cream of Wheat. I prefer COW to corn meal as it doesn't stink as much on firing and it has a scouring effect that keeps the barrel clean.
  
Back to top
 
IP Logged
 
moodyholler
Oldtimer
*****
Offline



Posts: 697
Location: Blue Ridge
Joined: Oct 11th, 2005
Re: Martini Cadet 32-357- need help
Reply #17 - Oct 13th, 2020 at 6:41pm
Print Post  
Cream of Wheat and thin layer of paraffin wax to seal case mouth. Melt a small amount in pan, let cool. And hold upside down and press case mouth up into wax. mh
  
Back to top
YIMAIM  
IP Logged
 
Philtillotson
Participating Member
*
Offline



Posts: 18
Joined: Oct 10th, 2019
Re: Martini Cadet 32-357- need help
Reply #18 - Oct 15th, 2020 at 10:54pm
Print Post  
Gentlemen- Thanks very much for the great ideas- never done that before- what kind of charge is typically required to form the case? recommendations on that? thanks again.
  
Back to top
 
IP Logged
 
Barrabruce
Junior Member
**
Offline



Posts: 71
Location: Australia
Joined: Mar 30th, 2017
Re: Martini Cadet 32-357- need help
Reply #19 - Oct 16th, 2020 at 8:10am
Print Post  
I use 2 grns of bulleye
A wad from a drink coaster 
Enough toilet paper shoved in firm to fill and another wad on top.

This is to Fire form 310 cadet cases from 32-20 cases.

Note the neck is flared to rub on the chamber when seated which help keep it aligned.
Clean the bore regularly with Ed’s red.
This works for me in a Martin cadet.
Your mileage may vary thou.
  
Back to top
 
IP Logged
 
Philtillotson
Participating Member
*
Offline



Posts: 18
Joined: Oct 10th, 2019
Re: Martini Cadet 32-357- need help
Reply #20 - Oct 17th, 2020 at 7:25pm
Print Post  
Barrabruce- good advice- thanks very much- forming cases without bullets is a new and interesting experiment for me and I look forward to it.
regards, Phil
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: 1 [2] 
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 0.9407 seconds.