ASSRA Forum - C&H bench priming w/auto feed

ASSRA Forum › General › Reloading the Single Shot Rifle › C&H bench priming w/auto feed

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Normal Topic

C&H bench priming w/auto feed (Read 2111 times)

830singleshot Senior Forum Member Offline Posts: 404 Location: Texas Joined: Feb 11^th, 2007	C&H bench priming w/auto feed Oct 4^th, 2020 at 12:16am	Print Post
	I guess I'm on a priming tool kick. While looking through my piles of stuff acquired though old estates, I found this C&H bench priming tool. It was missing the primer tubes and priming rams as well as a way to retain the shell holder. At first I thought it was going to accept standard RCBS parts. However, they were only the starting point. Here it is, up and running but not yet permanently mounted.
	« Last Edit: Oct 4^th, 2020 at 12:37am by 830singleshot »
	J. Scott McCash&&New Braunfels, TX&&830-237-2376&&jsmccash@yahoo.com
	IP Logged

830singleshot Senior Forum Member Offline Posts: 404 Location: Texas Joined: Feb 11^th, 2007	Re: C&H bench priming w/auto feed Reply #1 - Oct 4^th, 2020 at 12:19am	Print Post
	I used RCBS priming stems that come from either a ram or bench primer tools and shortened them 0.235
	« Last Edit: Oct 4^th, 2020 at 5:30pm by 830singleshot »
	J. Scott McCash&&New Braunfels, TX&&830-237-2376&&jsmccash@yahoo.com
	IP Logged

830singleshot Senior Forum Member Offline Posts: 404 Location: Texas Joined: Feb 11^th, 2007	Re: C&H bench priming w/auto feed Reply #2 - Oct 4^th, 2020 at 12:23am	Print Post
	I had some old RCBS primer tubes that fit perfectly but the hole for the clip was in the wrong place. I could have just drilled another hole, but if you put the clip in the wrong hole, the tube wouldn't be fully inserted and that would result in a primer spill. The solution was to shorten the tube and redrill

	J. Scott McCash&&New Braunfels, TX&&830-237-2376&&jsmccash@yahoo.com
	IP Logged

830singleshot Senior Forum Member Offline Posts: 404 Location: Texas Joined: Feb 11^th, 2007	Re: C&H bench priming w/auto feed Reply #3 - Oct 4^th, 2020 at 12:30am	Print Post
	I'm not sure what C&H used to retain shell holders, but I had a extra RCBS retaining clip. I spotted and drilled a hole for that. The priming arm was binding against the shell holder so I milled .025 clearance. I did a test run of 20 pieces of 40-65 brass and it worked perfectly other than I was just holding it in a vise. It just needs a little detailing and permanent mounting to be put to work. It was a simple little project and I was glad to bring it back to life

	J. Scott McCash&&New Braunfels, TX&&830-237-2376&&jsmccash@yahoo.com
	IP Logged

830singleshot Senior Forum Member Offline Posts: 404 Location: Texas Joined: Feb 11^th, 2007	Re: C&H bench priming w/auto feed Reply #4 - Oct 4^th, 2020 at 5:35pm	Print Post
	Well, here it is all prettied up and mounted on a piece of scrap 2x4 so it stays out of the way and clamps to the bench. It also provides a place to store the small & large tubes and rams. I like it better than the RCBS bench priming tool. PS. The target is behind the tool in the picture so you don't see the disaster on the bench

	J. Scott McCash&&New Braunfels, TX&&830-237-2376&&jsmccash@yahoo.com
	IP Logged

GT Frequent Elocutionist Offline Posts: 2041 Location: Northeast Wyoming Joined: Jun 28^th, 2015	Re: C&H bench priming w/auto feed Reply #5 - Oct 4^th, 2020 at 7:31pm	Print Post
	Scott, Thanks for sharing that. I recently went to a Frankford Arsenal hand held type after my ancient Lee tools all gave it up, it's nice. I had a RCBS bench model that I use to use and for some reason I can't recall??? got away from it... I like the features of the CH and your little mods, I think I still have one in my mess somewhere and when I get the new cave done it'll find a place on the bench. Greg you're suppose to share pictures of your mess... folks on here don't miss much when you do...

	"To invent, you need a good imagination and a pile of junk" T. A. Edison "The trouble ain't that there is too many fools, but that the lightning ain't distributed right" M.T.
	IP Logged

830singleshot Senior Forum Member Offline Posts: 404 Location: Texas Joined: Feb 11^th, 2007	Re: C&H bench priming w/auto feed Reply #6 - Oct 4^th, 2020 at 10:39pm	Print Post
	Here is a little something I'm not too ashamed of, but it's messy. My Southbend heavy 10. I bought this flexible arm light on Amazon for $13. It had a clip to mount it. Removed the clip and made a strap bracket to mount under the shelf and secured the on/off switch. Not very pretty but I can see great

	J. Scott McCash&&New Braunfels, TX&&830-237-2376&&jsmccash@yahoo.com
	IP Logged

JerryH Frequent Elocutionist Online ASSRA Member #10876 Posts: 1241 Location: Easton, CA Joined: Nov 9^th, 2014	Re: C&H bench priming w/auto feed Reply #7 - Oct 4^th, 2020 at 11:40pm	Print Post
	As we get older more light is always welcome. And as Greg said, "folks on here don't miss much". Tell us more about the speed controller on the wall. JerryH

	I'm not a complete idiot, some of my parts are missing.
	IP Logged

830singleshot Senior Forum Member Offline Posts: 404 Location: Texas Joined: Feb 11^th, 2007	Re: C&H bench priming w/auto feed Reply #8 - Oct 5^th, 2020 at 12:08am	Print Post
	Will do. Starting a new thread under gunsmithing

	J. Scott McCash&&New Braunfels, TX&&830-237-2376&&jsmccash@yahoo.com
	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 1.1286 seconds.