ASSRA Forum › General › Reloading the Single Shot Rifle › Bullet puller for lead bullets
(Moderator Group: Moderator)
‹ Previous Topic | Next Topic ›
Page Index Toggle Pages: [1] 2  Send TopicPrint
Hot Topic (More than 10 Replies) Bullet puller for lead bullets (Read 6387 times)
KFW
Oldtimer
*****
Offline



Posts: 554
Location: Powell Wy.
Joined: Dec 18th, 2016
Bullet puller for lead bullets
Sep 23rd, 2020 at 4:47pm
Print Post  
Ok I need to gently pull 100+ .40 cal 450 gr. 16:1 money bullets that have minimum neck tension. Going to need a collet that fits a .400" dia. nose. I do not want to use the hammer-inertia or pliers method. Can someone recommend a brand that you have used with good results? Driven by the need to not disturb the wad and compressed powder in the process.
Thanks
kw
  
Back to top
 
IP Logged
 
oneatatime
Frequent Elocutionist
*****
Offline



Posts: 3866
Location: Rocky Mountains
Joined: Oct 30th, 2011
Re: Bullet puller for lead bullets
Reply #1 - Sep 23rd, 2020 at 5:16pm
Print Post  
For lead bullets I gave up on collets and use a wire stripper laid flat on top of the press, squeeze into the sides of the bullet just above the case and lower the ram. EZ.
  
Back to top
 
IP Logged
 
Cbashooter
Frequent Elocutionist
*****
Offline



Posts: 1572
Location: Eastern Wa.
Joined: Mar 31st, 2018
Re: Bullet puller for lead bullets
Reply #2 - Sep 23rd, 2020 at 7:11pm
Print Post  
oneatatime wrote on Sep 23rd, 2020 at 5:16pm:
For lead bullets I gave up on collets and use a wire stripper laid flat on top of the press, squeeze into the sides of the bullet just above the case and lower the ram. EZ.



  Yup what he said
  
Back to top
 
IP Logged
 
boats
Frequent Elocutionist
*****
Offline



Posts: 7545
Location: Virginia
Joined: Apr 23rd, 2004
Re: Bullet puller for lead bullets
Reply #3 - Sep 23rd, 2020 at 7:38pm
Print Post  
Me too.

Boats
  
Back to top
 
IP Logged
 
Cbashooter
Frequent Elocutionist
*****
Offline



Posts: 1572
Location: Eastern Wa.
Joined: Mar 31st, 2018
Re: Bullet puller for lead bullets
Reply #4 - Sep 23rd, 2020 at 9:44pm
Print Post  
If I want to try to save the bullets I use RCBS impact bullet puller .i.dont use the supplied collet I just use standard press shell holders to hold the Rim of the case
  
Back to top
 
IP Logged
 
Jeff Houck
Junior Member
**
Offline



Posts: 78
Location: Pocatello
Joined: Jan 11th, 2014
Re: Bullet puller for lead bullets
Reply #5 - Sep 24th, 2020 at 12:01am
Print Post  
The wire cutter method works well for me too.
  
Jeff Houck
Back to top
YIMAIM  
IP Logged
 
KFW
Oldtimer
*****
Offline



Posts: 554
Location: Powell Wy.
Joined: Dec 18th, 2016
Re: Bullet puller for lead bullets
Reply #6 - Sep 24th, 2020 at 10:14am
Print Post  
Yes, a collet pull set up did not work well. I tried to pull them in my verticle mill. Went back to the hammer, found that a couple gentle taps to get 2 lube grooves exposed broke the lube suction and I could twist-pull them out with out dislodging the compressed powder wad column. Had to set barrel back 1 thread last week and run a new reamer in, then the cases did not seat by .062, so then resized/expanded & them re-seated the bullets and all is well for a test firing.
kw
  
Back to top
 
IP Logged
 
John Boy
Ex Member


Re: Bullet puller for lead bullets
Reply #7 - Sep 24th, 2020 at 12:34pm
Print Post  
Quote:
I need to gently pull 100+ .40 cal 450 gr. 16:1 money bullets that have minimum neck tension.

A kinetic bullet puller will separate the bullet from the case with minimum distortion to the bullet... based on my use of the puller pulling many bullets

Just think about it - the kinetic pullers are merely pushing the bullet out of the case- regardless of the tension in the case.  If the bullets were finger seated, there will be no distortion
  
Back to top
 
IP Logged
 
oneatatime
Frequent Elocutionist
*****
Offline



Posts: 3866
Location: Rocky Mountains
Joined: Oct 30th, 2011
Re: Bullet puller for lead bullets
Reply #8 - Sep 24th, 2020 at 12:46pm
Print Post  
He wasn't worried about the bullets, it was "with out dislodging the compressed powder wad column" beneath them that would have been disturbed by a kinetic puller.
  
Back to top
 
IP Logged
 
MartiniBelgian
Frequent Elocutionist
*****
Offline



Posts: 1675
Location: Aarschot
Joined: Jun 7th, 2004
Re: Bullet puller for lead bullets
Reply #9 - Sep 24th, 2020 at 3:16pm
Print Post  
No - only if you go about hammering like a madman, after the bullet is already out of the case.  If done with just a few gentle taps, the powder column won't budge, you just need to check as to whether the bullet is starting to move, and then proceed with even more caution.  Done this (too) many times, works quite well.
  
Back to top
WWW  
IP Logged
 
marlinguy
Frequent Elocutionist
*****
Offline


Ballards may be weaker,
but they sure are neater!

Posts: 16093
Location: Oregon
Joined: Feb 2nd, 2009
Re: Bullet puller for lead bullets
Reply #10 - Sep 24th, 2020 at 4:57pm
Print Post  
I've got a pretty complete set of collets and the tool they go with, and never use them. Worthless to me since I never load or shoot jacketed beyond a couple modern rifles. Need to take the whole setup to the next gun show if we ever have one again!
  
(You need to Login or Register to view media files and links)
Back to top
 
IP Logged
 
38-72
Junior Member
**
Offline



Posts: 98
Location: Lost In Washington State
Joined: Aug 4th, 2008
Re: Bullet puller for lead bullets
Reply #11 - Sep 24th, 2020 at 11:59pm
Print Post  
I use an 8" end cutting nipper with a deep throat.  It works great.

  
Back to top
 
IP Logged
 
4570mike
Senior Forum Member
****
Offline



Posts: 386
Location: On the Peninsula
Joined: Apr 11th, 2013
Re: Bullet puller for lead bullets
Reply #12 - Sep 25th, 2020 at 12:40pm
Print Post  
This works good.  You will need to re-cast the projectiles.
  
Back to top
 
IP Logged
 
oneatatime
Frequent Elocutionist
*****
Offline



Posts: 3866
Location: Rocky Mountains
Joined: Oct 30th, 2011
Re: Bullet puller for lead bullets
Reply #13 - Sep 25th, 2020 at 2:31pm
Print Post  
The possible problem with that (or using pliers the same way), Mike, is damaging the threads on the insert. Been there and done that once. That's why I now use a wire stripper placed flat across the top of the press. No chance of damaging the threads. Easier to use also.
  
Back to top
 
IP Logged
 
4570mike
Senior Forum Member
****
Offline



Posts: 386
Location: On the Peninsula
Joined: Apr 11th, 2013
Re: Bullet puller for lead bullets
Reply #14 - Sep 25th, 2020 at 2:46pm
Print Post  
oneatatime wrote on Sep 25th, 2020 at 2:31pm:
The possible problem with that (or using pliers the same way), Mike, is damaging the threads on the insert. Been there and done that once. That's why I now use a wire stripper placed flat across the top of the press. No chance of damaging the threads. Easier to use also.


I tried those and they do not lay flat across the top of the press causing the cartridge to tilt. These cutters are wide enough that they avoid the threads and grip much better than wire strippers.
Mike.
  
Back to top
 
IP Logged
 
Page Index Toggle Pages: [1] 2 
Send TopicPrint
‹ Previous Topic | Next Topic ›
 
  « Board Index ‹ Board Top  

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid RSS Valid XHTML Valid CSS Powered by Perl Source Forge

Page completed in 1.1654 seconds.