ASSRA Forum - My Accurate Hudson Mold...

ASSRA Forum › General › Reloading the Single Shot Rifle › My Accurate Hudson Mold...

(Moderator Group: Moderator)

‹ Previous Topic | Next Topic ›

Page Index Toggle

Pages: 1

Normal Topic

My Accurate Hudson Mold... (Read 2002 times)

John Boy Ex Member	My Accurate Hudson Mold... Aug 23^rd, 2020 at 10:51pm	Print Post
	32-40 and and 38-55 together


	IP Logged

Premod70 Oldtimer Offline Posts: 864 Location: North Carolina Joined: Jan 16^th, 2016	Re: My Accurate Hudson Mold... Reply #1 - Aug 24^th, 2020 at 9:35am	Print Post
	Purdy moles.


	IP Logged

wcf3840 Senior Forum Member Offline ASSRA Life #299 Posts: 354 Location: Palatine Joined: May 28^th, 2007	Re: My Accurate Hudson Mold... Reply #2 - Aug 24^th, 2020 at 10:51am	Print Post
	Great looking mold. I ordered one last Thursday and received it today. Tom's service is great!


	GTalk IP Logged

craigd Frequent Elocutionist Offline Posts: 2047 Location: midwest Joined: Feb 22^nd, 2009	Re: My Accurate Hudson Mold... Reply #3 - Aug 24^th, 2020 at 11:43am	Print Post
	That's what I have done to sort of get the second mold for a bargain, especially if it's a partial experiment thing, low expected volume thing. What I have found is I have better luck with rejects if both cavities are similar in size as far as casting from both cavities at the same time goes. I have both the Hudson molds, but have thought of ordering to fiddle with diameters. Maybe some day for the 38 for me.


	IP Logged

art_ruggiero Frequent Elocutionist Offline Posts: 1084 Location: CT Joined: Dec 14^th, 2008	Re: My Accurate Hudson Mold... Reply #4 - Aug 25^th, 2020 at 3:16pm	Print Post
	john boy are you happy with the allumenum mold? thanks art


	IP Logged

John Boy Ex Member	Re: My Accurate Hudson Mold... Reply #5 - Aug 25^th, 2020 at 5:17pm	Print Post
	Quote: john boy are you happy with the aluminum mold? Art -delighted with Accurate molds. Have about a half dozen. As good as Paul Jones & Brooks steel ones but much cheaper


	IP Logged

Cbashooter Frequent Elocutionist Offline Posts: 1570 Location: Eastern Wa. Joined: Mar 31^st, 2018	Re: My Accurate Hudson Mold... Reply #6 - Aug 25^th, 2020 at 7:11pm	Print Post
	I'm also very happy with accurate molfs. I've had him make a few for me and they cast beautiful.


	IP Logged

SSShooter Frequent Elocutionist Offline Posts: 2917 Location: Southern NJ Joined: Aug 1^st, 2010	Re: My Accurate Hudson Mold... Reply #7 - Aug 26^th, 2020 at 8:00am	Print Post
	art_ruggiero wrote on Aug 25^th, 2020 at 3:16pm: john boy are you happy with the allumenum mold? thanks art Accurate makes an excellent mold, based on the several I own. However, I find dual cavity molds a PITA to use and go for the smaller, lighter single-cavity molds. Also prefer brass as they hold the heat much better than aluminum and not much difference in cost, though gets the weight back up some amount.

	Glenn - 2x CPA 44 1/2 w/22LR (Shilen ratchet-rifled & Bartlein 5R rifled), 38-40RH & 38-55WCF (Bartlein 5R rifled) & 40-65WCF (GrnMtn 'X') barrels
	GTalk IP Logged

ratseye Full Member Offline Posts: 202 Location: Eastern, PA Joined: Feb 28^th, 2017	Re: My Accurate Hudson Mold... Reply #8 - Aug 27^th, 2020 at 7:21pm	Print Post
	All my Accurate molds are brass and I like them for holding heat. I'll put up with a bit of extra weight. Tom is a magician at getting them right. I have several custom molds from drawings I sent and he hits them exactly every time. He must live in the shop because the turnaround is usually fast. Thanks, ratseye


	IP Logged

Page Index Toggle

Pages: 1

‹ Previous Topic | Next Topic ›

« Board Index ‹ Board Top

Top

ASSRA Forum » Powered by YaBB 2.6.12!
YaBB Forum Software © 2000-2024. All Rights Reserved.

Valid XHTML

Valid CSS

Powered by Perl

Source Forge

Page completed in 0.4288 seconds.